Cargo, Hydrostatics & StabilityLastelære, hydrostatikk og stabilitet

Step-by-Step Draft Survey & Displacement Calculations

A technical deep-dive into the methodology of draft surveys, including perpendicular corrections, quarter-mean drafts, hydrostatic interpolation, Nemoto's trim corrections, and density adjustments to determine net cargo weight.

min readmin lesing
7
wordsord
1,359

UpdatedOppdatert 2026-11-19#draft-survey#bulk-carrier#displacement#ship-stability#cargo-operations#maritime-engineering

Core Concept & Why It Matters on Board

A draft survey is the primary method used in the bulk shipping industry to determine the weight of cargo loaded or discharged from a vessel. Unlike container ships, where cargo is counted by units, or tankers, where volumes are metered, bulk carriers (carrying ore, coal, grain, etc.) rely on the principle of Archimedes: the weight of the displaced fluid is equal to the weight of the vessel.

The fundamental equation of a draft survey is: Net Cargo Weight = (Final Displacement - Final Deductibles) - (Initial Displacement - Initial Deductibles) + Ship’s Constant

In the commercial sphere, the draft survey result forms the basis of the Bill of Lading (B/L). Discrepancies between the shipper’s weight (from shore scales) and the vessel’s draft survey can lead to:

  • Cargo Claims: Disputes over short-loading or over-loading.
  • Demurrage/Despatch Disputes: Errors in weight can affect the time taken for loading/discharging.
  • Letter of Protest: The Chief Mate must issue these when significant discrepancies are detected.

Safety and Stability Implications

Beyond commerce, displacement calculations are critical for:

  • Stability Management: Ensuring the vessel maintains adequate GM (metacentric height).
  • Stress Monitoring: Calculating bending moments and shear forces to prevent structural failure (hogging/sagging).
  • Draft Limits: Ensuring the vessel does not exceed its maximum allowable draft for specific ports or channels.

Key Formulas, Tables & Rules

1. Draft Meanings and Corrections

When reading drafts, the marks on the hull are rarely perfectly aligned with the vessel’s perpendiculars (FP - Forward Perpendicular, AP - After Perpendicular).

  • Perpendicular Correction: The distance from the draft mark to the perpendicular divided by the LBP (Length Between Perpendiculars), expressed as a draft correction.
  • Mean Draft (Trimmed): Used when the vessel is in a standard trim.
  • Quarter-Mean Draft (): Crucial when a vessel is significantly hogging or sagging. Note: Using a simple arithmetic mean in a hogging condition will underestimate the displacement.

2. Density Correction

Hydrostatic tables are typically calculated for seawater with a density of . If the vessel is in brackish water or fresh water, the observed displacement must be corrected.

3. Nemoto’s Trim Corrections

Standard hydrostatic tables provide displacement at a specific mean draft. However, the vessel’s trim affects the actual displacement. Nemoto’s method corrects the displacement for the difference between the displacement at the mean draft and the displacement at the actual trimmed drafts.

  • 1st Correction (): Adjusts for the difference between the mean draft and the draft at the center of flotation (LCF).
  • 2nd Correction (): Adjusts for the change in displacement due to the change in trim (often derived from the change in Trim Moment).

4. The Ship’s Constant

The “Constant” represents the weight of all items not accounted for in the deductibles (e.g., hull fouling, permanent ballast, small amounts of water in bilges, and inaccuracies in sounding). It is determined by comparing the weight of a known cargo loaded/discharged against the change in displacement.


Step-by-Step Worked Numerical Example

Scenario: The Capesize bulk carrier MS Bulk Titan is preparing to load a cargo of Iron Ore at a terminal in Brazil. The water density is measured at .

Step 1: Initial State (Before Loading)

1.1 Draft Readings (Observed):

Position Forward (m) Aft (m) Midship (m)
Port 8.20 9.50 8.80
Stbd 8.24 9.54 8.84

1.2 Corrected Drafts (Applying Perpendicular and Mean Corrections):

  • Assume Perpendicular corrections for Fwd = +0.05m and Aft = -0.04m.
  • Corrected Fwd (Mean):
  • Corrected Aft (Mean):
  • Corrected Mid (Mean):

1.3 Calculate Initial Trim and Quarter-Mean Draft:

1.4 Determine Initial Displacement from Hydrostatic Tables:

  • Using the ship’s Hydrostatic Table for (interpolated):

1.5 Apply Density Correction:

1.6 Initial Deductibles:

  • Fuel: 800t
  • Fresh Water: 150t
  • Ballast Water: 2,500t
  • Stores/Misc: 50t
  • Total Initial Deductibles = 3,500t

1.7 Initial Net Displacement:


Step 2: Final State (After Loading)

2.1 Final Draft Readings (Observed):

Position Forward (m) Aft (m) Midship (m)
Port 10.50 11.20 10.80
Stbd 10.54 11.24 10.84

2.2 Corrected Final Drafts:

  • Corrected Fwd (Mean):
  • Corrected Aft (Mean):
  • Corrected Mid (Mean):

2.3 Final Trim and Quarter-Mean Draft:

2.4 Final Displacement (Interpolated):

  • Using tables for (interpolated):
  • (Assume direct interpolation result)

2.5 Final Density Correction:

2.6 Final Deductibles:

  • Fuel: 750t (consumed during loading)
  • Fresh Water: 140t
  • Ballast Water: 500t (pumped out to make room for cargo)
  • Stores/Misc: 50t
  • Total Final Deductibles = 1,440t

2.7 Final Net Displacement:


Step 3: The Final Cargo Calculation

Assuming the Ship’s Constant is known from the previous voyage to be 450t.


Practical Operational Procedures & Chief Mate Checklists

Pre-Survey Preparation

A draft survey is only as accurate as the measurements provided. The Chief Mate must ensure:

  1. Visual Clarity: Draft marks must be clean and clearly visible. If not, they must be painted or cleaned before the survey begins.
  2. Stability of Water: The survey should not be conducted in heavy swell or strong currents, as this makes reading the draft marks impossible.
  3. Tank Soundings: All fuel, water, and ballast tanks must be sounded by a competent officer to ensure deductibles are precise.
  4. Ballast Control: Ensure no ballast water is being pumped in or out during the actual reading process.

Chief Mate’s Draft Survey Checklist

  • Draft Marks: Are all 6 marks (Fwd, Aft, Mid Port/Stbd) clearly legible?
  • Water Density: Has a hydrometer reading been taken in the midship area? Is the hydrometer calibrated?
  • Trim/List: Is the vessel’s list within acceptable limits () for accurate draft reading?
  • Deductibles:
    • Fuel oil/Diesel oil sounding completed.
    • Fresh water tank soundings completed.
    • Ballast water tank soundings completed.
    • Bilge/Slop tank levels checked.
  • Surveyor Presence: Are the independent surveyor’s readings being recorded simultaneously with the crew’s readings?
  • Documentation: Are all perpendicular corrections from the ship’s stability booklet ready?

Common Calculation Pitfalls, Hazards & Real-World Failure Modes

1. The “Hidden” Ballast Error

One of the most frequent causes of cargo shortages is “unaccounted ballast.” This occurs when water is trapped in a void space, a double-bottom tank with a faulty sounding pipe, or a tank that was partially pumped out but not fully emptied. If the initial ballast reading is lower than the actual volume, the calculated cargo will be erroneously low.

2. Density Miscalculation

Using the standard factor in a river port (where density might be ) without correcting the displacement will result in a massive error. In the example above, using instead of would have resulted in a discrepancy of nearly of cargo.

3. Improper Mean Draft Selection

In vessels with significant hull girder stress (hogging or sagging), using the arithmetic mean draft () instead of the Quarter-Mean Draft will lead to an incorrect displacement reading from the hydrostatic tables. This is because the volume of the ship is not distributed linearly along the length.

4. The “Constant” Drift

The Ship’s Constant is not actually constant. It changes due to hull fouling (growth on the bottom increases drag and weight) and the accumulation of scale in tanks. If the constant is not updated periodically through a “zero-cargo” survey, error margins will widen over the course of a charter.


Applicable IMO Codes & Standards

  • IMO International Code on Intact Stability (IS Code): Provides the framework for understanding how displacement affects the ship’s center of gravity and stability.
  • IMO Grain Code: While specific to grain, it outlines the rigorous requirements for stability and loading which are relevant to bulk carrier operations.
  • MARPOL Annex I: Governs the management of oil and ballast water, which directly impacts the “Deductibles” section of a draft survey.
  • SOLAS Chapter VI: Deals with the carriage of cargoes and the importance of accurate weight documentation.
  • ship-encyclopedia/stability/trim-and-stability.md
  • ship-encyclopedia/cargo-and-stability/hydrostatic-tables.md
  • ship-encyclopedia/cargo-and-stability/ballast-water-management.md
  • ship-encyclopedia/cargo-and-stability/stress-and-bending-moments.md