Navigation, COLREGs & WeatherNavigasjon, sjøveisregler og vær · Engineering system cardTeknisk systemkort

Integrated Shipboard Charting and Positioning Systems

On a modern bridge, ECDIS acts as the central navigational integrator, plotting continuous GNSS Position, Velocity, and Time (PVT) data alongside gyrocompass heading onto official Electronic Navigational Charts.

min readmin lesing
23
wordsord
5,045

#ECDIS#GNSS#Positioning#Bridge Systems

Part 1: System cardDel 1: Systemkort

Core Function

On a modern bridge, ECDIS acts as the central navigational integrator, plotting continuous GNSS Position, Velocity, and Time (PVT) data alongside gyrocompass heading onto official Electronic Navigational Charts1. Speed logs supply Speed Through Water (STW) and Speed Over Ground (SOG) for Dead Reckoning (DR) fallback and maneuvering3, while echo sounders measure live water depth to support under-keel clearance (UKC) verification alongside ECDIS safety contours7. Together, these systems sustain continuous route monitoring, ARPA collision-avoidance inputs, and automated anti-grounding alarms2.

Primary Operational Tasks

  • Route planning and geometry validation: Planning routes on Electronic Navigational Charts (ENCs) with automated indications when tracks cross the own-ship safety contour or enter user-specified proximity to prohibited areas and special-condition zones2.
  • Continuous positioning and DR fallback: Plotting live GNSS fixes every ≤2 s (≤0.5 s for high-speed craft), identifying discrepancies across independent positioning sources, and reverting to heading-and-speed DR upon GNSS loss2.
  • Route monitoring and look-ahead alerting: Monitoring cross-track deviation limits, projecting own-ship motion by a mariner-set look-ahead time to alarm before crossing safety contours, and alerting ahead of critical route points or proximity limits to dangers2.
  • Depth and UKC monitoring: Continuously measuring available water depth below the transducer, surface, or keel via echo sounder, recording 12-hour depth histories at ≤1-minute intervals, and supporting UKC monitoring alongside emerging S-102/S-129 data layers7.
  • Speed and distance quantification: Measuring longitudinal STW and dual-axis (fore-aft and athwartships) SOG plus cumulative distance run to drive ARPA target plotting, trial maneuvers, track control, and low-speed port berthing5.

System Interconnections

Bridge sensors exchange real-time telemetry primarily via IEC 61162-1 (serial NMEA 0183) and IEC 61162-2 (38,400 bit/s high-speed serial) sentences, alongside IEC 61162-450 Ethernet networking within Integrated Navigation Systems (INS)9.

Inputs Entering ECDIS

Source Sensor or System

Primary Parameters Fed

IEC 61162 Sentences / Interfaces

Operational Function in ECDIS

GNSS / EPFS

Latitude/longitude, fix quality, SOG/COG, datum, UTC

$--GGA, $--GLL, $--GNS, $--RMC, $--VTG, $--DTM, $--ZDA

Continuous own-ship positioning, datum alignment, time sync9

Gyrocompass / THD

True heading, heading status, rate of turn

$--HDT, $--THS, $--ROT (ROT evaluation depends on INS configuration)

Own-ship orientation, DR heading vector, look-ahead alignment1

Speed Log (SDME)

Longitudinal STW, dual-axis STW/SOG

$--VBW, $--VHW

DR speed vector, water- vs. ground-referenced maneuvering3

Echo Sounder

Depth below transducer, depth with keel/surface offset

$--DBT, $--DPT

Live depth display and UKC verification7

Radar / ARPA

Radar overlay and tracked target data

Radar overlay & target interfaces (specific video/target sentences omitted in consulted sources)

Radar-to-chart position verification and collision avoidance2

AIS Transponder

Target reports, static/voyage data, addressed/binary & alert msgs

!AIVDM, !AIVDO, ABK, $AIALR

Traffic overlay and AIS target DR tracking22

NAVTEX / MSI

Maritime Safety Information and navigational warnings

IEC 61174 (2015) MSI interface; S-124 product layer

Navigational warning portrayal (direct NAVTEX serial mapping omitted in consulted manuals)3

Outputs Distributed from Navigation Sensors and ECDIS

Receiving Equipment

Distributed Data

Interface / Standard

Operational Role

Trackpilot / Autopilot

Navigation/GNSS data, route and track commands

IEC 61162 / INS route transfer

Automated heading and straight-track keeping (mandatory ≥10,000 GT)3

Radar / ARPA

STW (VBW/VHW), SOG (VTG), heading

IEC 61162-1/-2 serial interfaces; THD interface

Mandatory STW feed to ARPA (≥10,000 GT) for target plotting and trial maneuvers1

AIS Transponder

Position, timing, heading, speed (via internal/external GNSS and ship sensors)

IEC 61162 / GNSS input

Dynamic traffic broadcasting and timing synchronization9

Voyage Data Recorder (VDR)

Position, heading, speed, depth, wind, video capture, ECDIS interface

IEC 61162 (NMEA 0183), Ethernet, RS-232/422, video; IEC 61174 (2015)

Continuous voyage data recording3

GMDSS Distress Equipment

Position and timing dependencies

IMO A.694(17) common GMDSS/navigational framework; DSC references

Distress alerting and timing (explicit ECDIS/GNSS-to-GMDSS wiring/sentences omitted in consulted sources)7

In addition, Bridge Alert Management (BAM) and the Bridge Navigational Watch Alarm System (BNWAS) exchange alert states and acknowledgements (ALR/ACK) with ECDIS under IMO MSC.302(87) and IEC 61174 (2015)3.

Redundancy & Criticality

SOLAS Chapter V Regulation 19 mandates tiered carriage requirements based on gross tonnage (GT) and vessel class, anchored by Regulation V/19.2.6, which requires that on all ships of 500 GT and upwards, failure of one piece of equipment must not reduce the ship's ability to meet the requirements of paragraph 2.125.

Tonnage / Vessel Scope

Mandatory Charting, Depth, Speed, and Integrated Requirements (SOLAS Chapter V)

≥300 GT & all passenger ships

Echo sounder (V/19.2.3.1), STW speed log, Transmitting Heading Device (THD), 9 GHz radar (V/19.2.3.2), and AIS (V/19.2.4: international ≥300 GT, all passenger, non-international cargo ≥500 GT)1

≥500 GT

Gyrocompass, rudder/propeller/thrust/pitch indicators, and single-equipment failure resilience (V/19.2.6)1

≥3,000 GT

Second radar (3 GHz or Administration-approved second 9 GHz radar; V/19.2.7.1)1

≥10,000 GT

ARPA (≥20 targets) connected to STW device, plus heading or track control system (V/19.2.8.2)1

≥50,000 GT

Rate-of-turn indicator (V/19.2.9.1) plus forward and athwartships SOG log (V/19.2.9.2); ships built on/after 1 July 2014 require separate STW and dual-axis SOG devices per MSC.1/Circ.14291

International voyages (ECDIS)

Phased carriage (July 2012–July 2018) for passenger ships ≥500 GT, tankers ≥3,000 GT, and cargo ships ≥10,000 GT (V/19.2.10), with independent backup arrangements (V/19.2.1.4, V/27)1

To fulfill SOLAS chart carriage rules, an ECDIS must be type-approved, run up-to-date ENCs, remain compatible with current IHO standards, and maintain adequate, independent backup arrangements capable of safe takeover and sustaining safe navigation for the remainder of the voyage under Appendix 6 of MSC.232(82) and MSC.530(106)2. Vessels typically achieve compliance via dual independent ECDIS installations3 or an up-to-date paper chart portfolio (which is mandatory whenever operating in Raster Chart Display System [RCDS] mode)12. While exact SOLAS V/19 paragraph 2.1 Electronic Position-Fixing System (EPFS) carriage clauses are not reproduced in the consulted excerpts, MSC.232(82) §11.4.7 mandates continuous positioning and advises providing a second independent positioning source, preferably of a different type2. As highlighted in maritime training guidance citing the 2019 Stena Impero incident, relying solely on two identical GPS receivers creates a false sense of redundancy because both share identical susceptibility to RF jamming and spoofing3.

Part 2: Technical deep diveDel 2: Teknisk dybdeanalyse

1. ECDIS Architecture & Chart Formats

ECDIS loads official hydrographic vector Electronic Navigational Charts (ENCs) and their updates into an internal System Electronic Navigational Chart (SENC) database, rendering S-57 chart data on screen in accordance with IHO S-52 display standards10. Where official vector ENCs are unavailable for a sea area, type-approved ECDIS units may operate in Raster Chart Display System (RCDS) mode using Raster Navigational Charts (RNCs) under MSC.232(82) §1.9 and Appendix 7, though substantial differences govern automated alerting and legal carriage10.

Technical Attribute

S-57 ENC (Legacy Vector)

S-101 / S-100 ENC (Next-Gen Vector)

RNC in RCDS Mode (Raster)

Governing Standards

IHO S-57, S-52; IMO MSC.232(82)10

IHO S-100, S-98, S-101; IMO MSC.530(106)/Rev.137

MSC.232(82) §1.9 & Appendix 721

Data Structure

Layered vector chart features stored in SENC10

Modular vector chart (S-101) integrating gridded bathymetry (S-102), water levels (S-104), and currents (S-111)15

Paper-chart-derived raster display lacking layered vector objects12

Anti-Grounding Alarms

Automated against safety contour & prohibited areas10

Automated; dynamic safety contour generation via S-102 bathymetry37

No automatic anti-grounding alarms; requires manual clearing lines & danger markers12

Boundary & Datum Behavior

No displayed chart boundaries; layered vector content10

Multi-product portrayal integration (S-98)15

Visible chart borders; apparent position shifts may occur at grid intersections12

Legal Carriage Condition

Valid primary chart with Appendix 6 backup2

Valid in dual-fuel systems (mandatory for new/retrofit from 1 Jan 2029)35

Permitted only where ENCs are inadequate AND with up-to-date paper charts10

Adopted in November 2022 and updated via Resolution MSC.530(106)/Rev.1 on 24 May 2024 to support standardized ship-shore S-421 route plan exchange, the revised IMO ECDIS Performance Standards establish the regulatory framework for IHO S-100 interoperability35. As of 1 January 2026, newly installed ECDIS systems may comply with either legacy MSC.232(82) or MSC.530(106)/Rev.1; however, UK Hydrographic Office (ADMIRALTY) guidance notes that unpublished type-approval testing standards delay immediate certified S-100 deployment, with marine supplier guidance estimating type-approved S-100 hardware around 202835. From 1 January 2029, every newly installed or retrofitted ECDIS must comply with MSC.530(106)/Rev.135. Existing working S-57 ECDIS units face no mandatory replacement requirement, and new S-100 equipment must maintain "dual-fuel" capability to support both legacy S-57 ENCs and S-101/S-100 data35. IHO's Phase 1 S-100 rollout targets real-time route monitoring through S-101 (ENCs), S-102 (bathymetric surface), S-104 (real-time tidal water levels), S-111 (surface currents), S-124 (navigational warnings), S-128 (catalogue of nautical products), and S-129 (under-keel clearance management)15.

The Safety Contour forms the critical hydrographic boundary separating safe navigable water from unsafe shoals10. Locked permanently within the mandatory Display Base, it is double-coded visually with a thick line and a prominent transition in depth shading (using two-shade or four-shade palettes)10. If the mariner leaves the setting unspecified, ECDIS defaults to 30 m; if the chosen (or 30 m default) contour does not exist in the active SENC—or becomes unavailable upon transitioning onto another chart—ECDIS automatically defaults to the next deeper contour available and alerts the mariner2. Under S-100/S-98 portrayal rules, wherever S-102 bathymetric grid coverage exists (marked by a boundary line using color token DEPWL), ECDIS constructs the safety contour directly from common rectangular S-102 grid edges matching the threshold while suppressing underlying S-101 Depth Area, Dredged Area, and Depth Contour features37.

By contrast, the Safety Depth serves solely as a visual reference threshold emphasizing spot soundings equal to or shallower than the selected value in bold numerals when spot soundings are displayed; breaching a shallow spot sounding does not trigger look-ahead anti-grounding alarms2. As illustrated in maritime training handouts (e.g., AESM SMS policy examples), operators frequently calculate safety depth from static draft, maximum squat, environmental variables (swell, siltation, pipeline reductions, ice accretion), and water-area UKC margins—such as adding 10% of static draft in pilotage channels, 20% in coastal waters under 25 NM, and 50% in open ocean beyond 25 NM10.

During route monitoring, ECDIS continuously queries the largest-scale SENC data available for own ship's region to evaluate alarms across a mariner-set look-ahead time (often termed the look-ahead function or guard zone), triggering alarms whenever the vessel is projected to cross the safety contour or enter prohibited/special-condition zones, as well as alerts at set distances/times prior to dangers, aids to navigation, and critical route points2. However, SCAMIN (Scale Minimum)—an ENC attribute dictating the smallest viewing scale at which an object renders—can conceal wrecks, obstructions, depth contours, and aids to navigation if officers monitor transits on an undersized scale, creating a false sense of safety10. Furthermore, IMO Circular MSC.1/Circ.1503/Rev.1 highlights documented ECDIS anomalies in which small point land features depicted only on small-scale (usage band 1 and 2) ENCs may be obscured by surrounding chart detail or fail to trigger route-planning/monitoring alarms on certain equipment12.

Under MSC.232(82) / MSC.530(106) §14 and Appendix 6, approved backup arrangements must be independent, enable rapid safe takeover before a critical situation develops, and permit safe navigation for the entire remaining voyage2. ECDIS must also continuously store and play back the preceding 12 hours of navigation reconstruction data and official database verification at 1-minute intervals2.

2. GNSS / GPS & Augmentation Systems

Shipboard Positioning, Navigation, and Timing (PNT) relies on multi-system radionavigation receivers governed by IMO Resolution MSC.401(95) (and revised MSC.432(98)) and tested under the IEC 61108 standards series14. Resolution MSC.401(95) specifies multi-constellation receivers utilizing at least two independent GNSS networks to safeguard PVT availability and integrity4.

Constellation

Operational Baseline & Modernization (Status as of late 2026)

Civil Signals & Authentication Services

GPS

Operational since 1995; Standard Positioning Service commits to ~9 m (95%) horizontal error4

Legacy L1 C/A plus modernized L2C (1227 MHz, first launched 2005, pre-operational), L5 (1176 MHz, first full transmitter May 2010, pre-operational), and L1C (1575 MHz, first launched Dec 2018, developmental) per gps.gov summaries43

Galileo

Civilian system; Initial Services Dec 2016; GSC status on 23 Oct 2026 reported 28 usable and 4 unusable satellites43

Open Service on E1 (E1-B I/NAV) and E5 (E5a/E5b), SAR return link, E6 High Accuracy Service (HAS, live Jan 2023), and E1-B OSNMA (operational 24 Jul 2025)43

GLONASS

MEO constellation transitioning to GLONASS-K1/K2 (from 2020 onward); post-2025 plans documented for six HEO GLONASS-V satellites44

Standard civil navigation signals (frequency/authentication modernization ongoing per EUSPA reports)44

BeiDou (BDS-3)

Fully deployed globally since June 2020 with 30 satellites (supplemented regionally by NavIC and QZSS)43

Global multi-frequency Open Service civil positioning43

Under MSC.401(95) technical criteria, receivers must acquire a valid PVT solution within 5 min from a cold start (no valid almanac), 1 min from a warm start (valid almanac), and 2 min after power interruptions or signal outages under 60 s, maintaining UTC (BIPM) accuracy within 0.1 s and generating fixes at least every 2 s (or 0.5 s on high-speed craft)4.

To improve coastal accuracy and provide timely integrity warnings, receivers process Differential GNSS (DGNSS) corrections broadcast by terrestrial IALA beacons (IEC 61108-4) or Satellite-Based Augmentation Systems (SBAS), such as Europe's EGNOS (PRNs 120, 123, 136)46. In a two-year peer-reviewed study published in Sensors (2020) across 108 coastal and island stations from May 2016 to April 2018 (63,072,000 s), EGNOS achieved 99.999% signal availability (only 14 s of simultaneous signal-in-space absence) and 0.91 m 95th-percentile Horizontal Position Error (HPE)—comfortably inside IMO A.1046(27)'s 10 m coastal limit—yet reached 93.62% aggregate station compliance against strict 15-minute continuity criteria, leading researchers to recommend revising maritime SBAS continuity assumptions4. Formalizing maritime SBAS testing under IEC 61108-7 (including EGNOS/ESMAS support) remains an active regulatory effort28.

For geodetic consistency, ECDIS processes IEC 61162 $--DTM (Datum Reference) messages and enforces IMO MSC.232(82) requirements that ECDIS and all overlaid navigational inputs share a common reference system, issuing an indication whenever a mismatch exists9. When vessels operate with raster charts based on heterogeneous paper datums, residual datum differences can manifest as visible position shifts at chart borders and grid intersections12. Note that while $--DTM interfacing, common-datum alerts, and RNC grid-shift hazards are documented in the consulted standards, explicit WGS-84 ellipsoid parameters and mathematical datum-transformation equations are omitted in the retrieved excerpts.

Because GNSS satellites orbit ~20,000 km above Earth, arriving signals are extremely weak and vulnerable to solar weather as well as intentional RF interference27. In a Royal Institute of Navigation (RIN) survey of 271 mariners, 75% rated GNSS interference impacts on safety and port security as very serious, noting that more than 20 onboard systems across 7 categories process GNSS position or timing27. An IALA radionavigation workshop report (updated February 2026) documents persistent jamming and AIS spoofing incidents in regions such as the Baltic Sea and Eastern Mediterranean28. Disruption mechanisms span jamming (RF blocking/overpowering), spoofing (transmitting false signals, including data-level ephemeris and clock attacks), and meaconing (recording and rebroadcasting genuine GNSS signals)27.

Defense Layer

Mechanism & Operational Status (as of late 2026)

Threat Coverage & Key Limitations

Galileo OSNMA

Declared operational 24 July 2025; inserts TESLA cryptographic authentication in reserved 40-bit fields of E1-B I/NAV using GSC public keys and a trusted time source (accurate within 5 min)43

Flags spoofed navigation messages with zero positioning overhead; does not defeat jamming or authenticate ranging codes (future Galileo E6 Signal Authentication Service [SAS] targets ranging authentication)43

Multi-Constellation Advanced RAIM

Cycles pseudorange consistency checks across GPS, Galileo, BeiDou, and GLONASS clusters49

Detects single-constellation faults or isolated spoofing; fails if all visible frequency bands are denied or spoofed coherently27

Hardened Antennas (CRPA / Helical)

Adaptive null-steering CRPAs suppress directional jamming and in some designs spoofing27; sky-pointed high-gain helical antennas reject low-angle emitters (vendor specs claim up to ~40 dB jamming suppression)49

Protects against horizon/shore-based jamming and low-angle spoofing27; increases installation cost and complexity

Terrestrial R-Mode

IALA-backed ranging over existing MF DGNSS (~300 kHz) and VDES (embedding ranging sequences into 26.67 ms time slots during GNSS outages)28

Delivers resilient coastal/port multilateration independent of satellite RF links28

Operational Hygiene

Disabling built-in NAVTEX GNSS before entering interference zones (24% mariner failure rate reported), radar/visual cross-fixing, VTS/NAVWARN reporting3

Essential baseline fallback; depends heavily on crew proficiency and non-digital navigation skills3

3. Echo Sounder Physics & Transducers

Mandated under SOLAS V/19.2.3.1 for all passenger ships and all ships ≥300 GT, navigational echo sounders conform to IMO Resolution MSC.74(69) Annex 4 (amending A.224(VII)) and ISO 98751.

Marine echo sounders excite hull-mounted ceramic crystal transducers parallel-tuned to high-voltage radiofrequency (RF) emitters, projecting acoustic pulses downward and timing seabed echoes7. Because water provides essential acoustic coupling and damping, energizing an echo sounder while drydocked irreparably damages the ceramic crystals8. Note that while manuals document ceramic crystal hardware, high-voltage RF tuning, and ISO 9875 carrier-frequency/pulse-width tests7, explicit piezoelectric electromechanical coupling equations are absent from the consulted sources.

For acoustic pulse travel-time calculation, MSC.74(69) and ISO 9875 anchor depth conversion to a nominal seawater sound velocity of 1500 m/s—meaning indicated water depth equals half the round-trip pulse travel time multiplied by 1500 m/s7. Raw transducer-to-seabed clearance (DBT — Depth Below Transducer) is adjusted by installer offsets to output either Depth Below Surface (DBS) (adding transducer immersion draft) or Depth Below Keel (subtracting transducer-to-keel offset via IEC 61162 $--DPT sentences)8. Misreading DBS as keel clearance in shallow approaches introduces immediate grounding risk8.

Dual-frequency sounders exploit contrasting acoustic properties between low- and high-frequency channels55. In commercial systems such as the Furuno FE-700, the 50 kHz channel produces a wide beamwidth with stronger deep-water penetration and a minimum measurable range of 2.0 m, whereas the 200 kHz channel produces a narrow beamwidth with finer shallow-water resolution (minimum range 0.5 m) and superior immunity to aeration bubbles when going astern or steaming in heavy seas55. However, regulatory compliance strictly restricts primary frequency selection: Wheelmark type-approved equipment manuals (e.g., F-3000W) explicitly warn that official carriage compliance requires 50 kHz or 100 kHz operation, whereas 200 kHz readings are not officially approved and must not be used for navigation8.

Echo sounder accuracy degrades across several environmental and hydrodynamic mechanisms. Entrained aeration bubbles from bow thrusters, astern wash, or pitching seas scatter wide-beam low-frequency energy; consequently, SOLAS V/19 §8 mandates siting transducers clear of underwater hull openings and projections11. Roll, pitch, heel, and trim tilt the acoustic axis off vertical and shift effective keel depth, and ISO 9875 accuracy tolerances explicitly exclude ship rolling and pitching7. Dynamic squat reduces actual under-keel clearance at speed in shallow channels; rather than being compensated directly by echo sounders, squat must be calculated and incorporated into ECDIS Safety Depth and UKC margins10. Changes in seawater temperature, salinity, and pressure shift true sound speed away from the 1500 m/s baseline, while fish schools, organic matter, and suspended residues trigger spurious echoes requiring MSC.74(69)-mandated interference suppression7 (explicit thermocline ray-bending models are omitted in the consulted manuals). Finally, in hard-bottom shallow waters, multiple reflections can cause digital displays to lock onto the second bottom echo, displaying twice the true water depth unless cross-checked against the graphic echogram and chart soundings8.

4. Speed Log Technologies (EM vs. Doppler)

Shipborne Speed and Distance Measuring Equipment (SDME) complies with IMO Resolutions A.824(19), MSC.96(72), MSC.334(90), and IEC 610235. As mechanical logs susceptible to physical wear have largely been phased out except on small craft, commercial bridges rely on Electromagnetic (EM) logs and Doppler/Correlation acoustic logs6.

Electromagnetic logs operate as single-axis relative logs measuring longitudinal Speed Through Water (STW)6. Sensors employ either a fixed hull probe or a retractable gate-valve stem protruding below the vessel's turbulent hydrodynamic boundary layer6. Classification rules mandate that retractable probes extend, operate accurately, and retract safely across the vessel's entire speed range with clear position indication6. Commercial EM logs (e.g., YDK EML900) satisfy MSC.96(72) ±2% or ±0.2 knot speed tolerances57. Note that while boundary-layer protrusion, retractable mechanics, single-axis STW operation, and accuracy compliance are verified in the consulted manuals and guidelines6, explicit descriptions of Faraday's law of induction, AC excitation coils, and sensing-electrode voltage measurement are absent from those texts.

Doppler Velocity Logs (DVLs) derive vessel speed from the acoustic Doppler frequency shift between emitted sound pulses and echoes returned from the seabed or water column6. Unlike single-axis EM probes, dual-axis and three-axis acoustic logs measure both fore-aft and athwartships motion—essential for large ships ≥50,000 GT experiencing leeway from beam winds and cross-currents in narrow channels and port berthing5. DVLs commonly interleave two measurement modes61: Bottom-Track Mode measures true Speed Over Ground (SOG) from stationary seabed returns (VBW ground fields), operating between minimum clearances of ≥2 m to ≥3 m beneath the transducer and maximum depths around 250 m (e.g., JRC JLN-900 using 150 kHz for 3-axis SOG up to 40 knots; SAL T2)20; Water-Track Mode measures STW (±50 knots range on JLN-900 and SAL T2) from water-column scatterers regardless of total ocean depth6. Advanced correlation units such as the JLN-900 pair 150 kHz SOG with a 3.8–4.2 MHz correlation STW transducer sampling a water volume 120–140 mm below the hull face64. Note that under SOLAS V/19.2.9.2 and MSC.1/Circ.1429 for ships ≥50,000 GT built on or after 1 July 2014, regulatory guidance emphasizes installing two functionally separate STW and dual-axis SOG devices without shared single points of failure5, whereas JRC vendor literature markets the combined JLN-900 as class-recognized to satisfy MSC.334(90) via separated measurement paths64.

DVL hardware employs either multi-beam Janus piston arrays or Phased Array transducers59. Teledyne RDI documentation specifically addresses phased-array sound-speed behavior for horizontal bottom-track velocity66, whereas standard piston DVLs apply an EC / SVP scale factor relative to 1500 m/s, requiring external SVP/CTD sensors or manual salinity entry accurate to ±1‰ (35 ppm saltwater / 0 ppm freshwater) and depth accurate to ±0.5 m65. Because water-track logs sense STW rather than ground track, sea-trial calibration per vendor calibration procedures runs reciprocal courses over a known distance (D NM in T seconds) so opposing currents average out, computing true water speed as V = (D / T) × 3600 knots68.

Feature

Electromagnetic (EM) Log

Dual-Axis Doppler / Correlation Log

Measurement Principle

Hull-protruding sensor in undisturbed flow (Faraday/electrode theory omitted in consulted sources)56

Acoustic Doppler shift and/or acoustic correlation6

Transducer Geometry

Fixed or retractable single-axis boundary-layer probe6

Flush/gate-valve Janus piston or Phased Array59

Measured Reference Frame

STW only (relative log)6

Both STW (water-track) and SOG (bottom-track)6

Directional Axes

Single-axis (fore-aft)56

Dual-axis (fore-aft and athwartships) or 3-axis5

Operational Depth Limits

Independent of water depth6

SOG requires ≥2–3 m clearance, max ~250 m depth; STW works in any depth ≥2–3 m62

SOLAS ≥50,000 GT Role

Satisfies mandatory STW requirement (paired with separate SOG unit)1

Satisfies mandatory dual-axis SOG (and STW where class-accepted with separated paths)5

5. Sensor Integrity, Alarms & Failure Modes

When continuous GNSS input fails, ECDIS triggers a position-loss alarm under MSC.232(82) and IEC 61174 and automatically enters Dead Reckoning (DR) mode, projecting own-ship position from connected gyrocompass heading and speed log data2. If both gyro and log fail, watchkeepers can enter manual heading and speed, though positional error compounds rapidly over time3. Per MSC.232(82) §11.4.14–15.1, ECDIS allows manual position offsets (always flagged by a persistent screen indicator that must be cleared once GNSS returns) and manual plotting of bearing/distance Lines of Position (LOP)3. Maritime training guidance citing INTERTANKO recommends cross-checking ECDIS position every 30 minutes in port approaches, 1 hour in coastal transits, and 4 hours in open ocean, while OCIMF recommends combining at least three independent verification methods such as visual bearings, radar overlays, and parallel indexing3.

Integrated bridges compliant with IMO MSC.252(83) (IEC 61924-2) and MSC.302(87) continuously cross-check active GNSS against secondary positioning sensors and DR estimates31. When divergence between sensors—or between GNSS and DR—exceeds a user-configured Discrepancy Limit, ECDIS issues an alert29. One recommended dual-ECDIS resilience practice connects GNSS inputs to the primary ECDIS while configuring the secondary unit to compare GNSS against DR3; however, maritime PNT research cautions that DR comparison reliably catches only sudden position jumps and may miss gradual spoofing drift72. Under MSC.302(87) and IEC 61924-2, bridge alerts follow a strict hierarchy—Alarm (A) for urgent conditions such as safety contour breaches or sensor loss, Warning (W), and Caution (C)—managed via ALR/ACK state transitions (V = active-unacknowledged)9. Under MSC.232(82) §11.4.8, alerts passed from external position, heading, or speed sensors appear on ECDIS strictly as indications rather than duplicated alarms36. While INS systems integrate telemetry over IEC 61162-450 Ethernet16, explicit Consistent Common Reference Point (CCRP) lever-arm offset equations are absent from the consulted manuals.

Hardware degradation and installation errors create critical non-electronic failure vectors. Siting echo sounder or speed log transducers near hull openings or projections violates SOLAS V/19 §8 and causes turbulent aeration11; for example, degraded acoustic conditions force Doppler logs such as the SAL T2 into "interpolation mode," relaxing accuracy from ≤0.1 kn / 1% down to ≤0.2 kn / 2%62, while missing STW measurements display --.-- kn on units like the JLN-740/74174. Wrong sound-speed scaling (EC/SVP), uncalibrated speed-log scale factors, and incorrect echo-sounder draft or keel offsets corrupt displayed readings8, mechanical logs suffer progressive physical wear6, and energizing echo sounders drydocked permanently destroys ceramic crystals8. Note that while siting, aeration, calibration drift, mechanical wear, and drydock burnout are documented, quantitative empirical degradation rates from biological transducer fouling (marine growth) are absent from the consulted sources.

System / Domain

Governing Standards

Parameter

Mandatory Performance Limit

GNSS (Ocean)

IMO A.1046(27), MSC.401(95)

Horizontal Accuracy (95%)

≤100 m; signal availability ≥99.8%; update rate ≤2 s4

GNSS (Harbor Entrances, Approaches, Coastal)

IMO A.1046(27), MSC.401(95), IEC 61108

Horizontal Accuracy (95%)

≤10 m; availability ≥99.8%; continuity ≥99.97% (over 15 min); update rate ≤2 s (≤0.5 s HSC); Time to Alarm <10 s4

GNSS (Timing)

IMO MSC.401(95) / MSC.432(98)

UTC (BIPM) Accuracy

Within 0.1 s14

Echo Sounder

IMO MSC.74(69) Annex 4, ISO 9875

Depth Accuracy (0–30 kn)

±0.5 m (20 m range), ±5 m (200 m range), or ±2.5% of depth (whichever greater), at 1500 m/s nominal sound speed (excluding roll/pitch)7

Echo Sounder

IMO MSC.74(69) Annex 4, ISO 9875

Depth Logging & Playback

Continuous recording of latest 12 hours at ≥1-minute intervals7

Speed Log (SDME)

IMO A.824(19), MSC.96(72), MSC.334(90), IEC 61023

Digital Speed & Serial Output

Within ±2% of ship speed or ±0.2 knots (whichever greater); digital display step ≤0.1 kn6

Speed Log (SDME)

IMO MSC.96(72), MSC.334(90)

Analogue Speed Display

Within ±2.5% of ship speed or ±0.25 knots (whichever greater); 0.5 kn grid with 5 kn digital marks6

Speed Log (SDME)

IMO MSC.96(72), IEC 61023

Distance Run

Within ±2% of distance run in 1 hour or ±0.2 NM (whichever greater); display range ≥9999.9 NM with ≤0.1 NM step6

ECDIS

IMO MSC.232(82), MSC.530(106), IEC 61174

Voyage Recording

Minimum 12 hours of navigation reconstruction & official database verification at 1-minute intervals2

References

  1. SOLAS V Carriage Requirements for Ships | PDF | Radar | Tonnage, https://www.scribd.com/document/801592218/Bridge-Equipment-Requirement
  2. RESOLUTION MSC.232(82) (adopted on 5 December 2006, https://wwwcdn.imo.org/localresources/en/KnowledgeCentre/IndexofIMOResolutions/MSCResolutions/MSC.232(82).pdf
  3. ECDIS Sensor Inputs & Position Verification Best Practices, https://www.marinepublic.com/blogs/training/399752-ecdis-sensor-inputs-position-verification-best-practices
  4. (PDF) EGNOS 1046 Maritime Service Assessment - ResearchGate, https://www.researchgate.net/publication/338379629_EGNOS_1046_Maritime_Service_Assessment
  5. Speed Log Requirement for Ships Above 50,000 GT - Knowledge, https://www.saiyangmarine.com/info/speed-log-requirement-for-ships-above-50-000-g-103644179.html
  6. N-07 SPEED LOG, https://www.ccs.org.cn/ccswzen/file/download?fileid=201950000000002294
  7. N-08 SOUNDER, https://www.ccs.org.cn/ccswzen/file/download?fileid=201950000000001629
  8. F-3000W Echo Sounder Manual | PDF - Scribd, https://www.scribd.com/document/130721182/F-3000W-REF-Manual-Ed-3-1-pdf
  9. Wartsila TM Platinum IEC Interface | PDF | Global Positioning System, https://www.scribd.com/document/728123652/Wartsila-TM-Platinum-IEC-Interface
  10. ECDIS Overview and Components Guide | PDF | Computing - Scribd, https://www.scribd.com/document/878889570/ECDIS-Handout
  11. SOLAS Chapter V Reg 19: Navigation Equipment | PDF - Scribd, https://www.scribd.com/document/683245578/Solas-Chapter-v-Regulation-19-Carriage-Requirements-for-Shipborne-Navigational-Systems-and-Equipment
  12. MSC.1/Circ.1503/Rev.1 16 June 2017 ECDIS – GUIDANCE FOR, https://www.classnk.or.jp/hp/pdf/activities/statutory/ism/imo/msc1-circ1503-rev1.pdf
  13. GUIDELINES FOR SURVEY OF ELECTRONIC CHART DISPLAY, https://www.ccs.org.cn/ccswzen/file/download?fileid=201950000000001116
  14. N-10 Multi-system Shipborne Radionavigation Receivers, https://www.ccs.org.cn/ccswzen/file/download?fileid=201950000000002134
  15. Navigating the Future: The Introduction of the S-100 ECDIS Standard, https://www.westpandi.com/news-and-resources/news/july-2026/navigating-the-future-the-introduction-of-the-s-10/
  16. Synapsis System Manual - Anschuetz, https://www.anschuetz.com/fileadmin/user_upload/Anschuetz/Approvals/operation_manuals/synapsis_system_manual/10000000964_SYNAPSIS_System_Manual_05.03.xx.pdf
  17. vdr100g3 PDF | PDF | Electrostatic Discharge | Usb - Scribd, https://www.scribd.com/document/457501119/vdr100g3-pdf
  18. SAM Platinum 2 Operations Manual.pdf - pdfcoffee.com, https://pdfcoffee.com/sam-platinum-2-operations-manualpdf-pdf-free.html
  19. SOLAS - Navsregs, https://navsregs.wordpress.com/category/solas/
  20. Navigator Doppler Velocity Log (DVL) Technical Manual, https://www.teledynemarine.com/en-us/resources/Documents/Brand%20Support/RD%20INSTRUMENTS/Technical%20Resources/Manuals%20and%20Guides/WorkHorse%20Navigator/Navigator%20Technical%20Manual_Jun20.pdf?csf=1&e=ZjOB6m
  21. MSC.232(82) Adoption of the Revised Performance Standards for, https://rise.odessa.ua/texts/MSC232_82e.php3
  22. TECDIS Installation Manual Overview | PDF - Scribd, https://www.scribd.com/document/474789863/TECDIS-Installation-Manual-EN-rev-3-02
  23. Marine Radar ARPA Safety Instructions | PDF - Scribd, https://www.scribd.com/document/594989030/FAR21x7-Operator-s-Manual
  24. OPERATOR'S MANUAL, https://www.furuno.it/docs/OPERATOR%20MANUALOME44730M_FMD3200_FMD33000.pdf
  25. SOLAS Chapt 5 Safety of Navigation Regulation 19 | PDF - Scribd, https://www.scribd.com/document/1013146069/SOLAS-Chapt-5-Safety-of-Navigation-Regulation-19
  26. SAM Electronics Platinum Trackball Guide | PDF | Wireless - Scribd, https://www.scribd.com/document/908818649/SAM-ECDIS
  27. IMPACTS OF GNSS INTERFERENCE ON MARITIME SAFETY, https://cdn.ymaws.com/rin.org.uk/resource/resmgr/maritime_report/the_rin_maritime_report_v1.2.pdf
  28. WORKSHOP REPORT 09 to 13 February 2026 Northern Lighthouse, https://www.iala.int/content/uploads/2026/03/Report-on-the-Workshop-on-Radionavigation-and-Radiocommunication.pdf
  29. JAN-7201/9201 - JRC World, https://www.jrc-world.com/files/secured/docuware_documents/190-ECDIS+JRC+JAN-7201-9201+Instruction+Manual+Reference+01-08-2025.pdf
  30. HLD-InS 600 User Manual | PDF | Computing - Scribd, https://www.scribd.com/document/830305747/HLD-InS-600-User-Manual
  31. User Manual for - Danelec Marine ECDIS Software V3.xx, https://cdn.prod.website-files.com/6971ef1bba37770e1af71170/6ac79933477949cbcaaacf6a_Danelec%20Marine%20ECDIS%20-%20User%20Manual.pdf
  32. guidance for use of ecdis,ais, vdr and bnwas for purpose of safe, https://dma.gov.mm/wp-content/uploads/2017/02/1.....directive-6-2018-use-of-ecdisaisvdr-and-bnwas-for-purpose-of-safe-navigation.pdf
  33. S-100 Standards in Force | IHO, https://iho.int/en/s-100-standards-in-force-0
  34. RESOLUTION MSC.530(106) (adopted on 7 November 2022, https://wwwcdn.imo.org/localresources/en/KnowledgeCentre/IndexofIMOResolutions/MSCResolutions/MSC.530(106).pdf
  35. S-100 ECDIS Explained: 2026 and 2029 Dates for Shipowners, https://www.avatecmarine.com/s-100-ecdis
  36. RESOLUTION MSC.232(82) - (adopted on 5 December 2006), http://jsmqa.or.jp/kaiji/kaijiDayori.pdf/MSC.%20232(82).pdf
  37. Harmonised User Experience for ECDIS and INS, https://iho.int/uploads/user/pubs/standards/S-98/S-98%20Annex%20C_Ed%201.0.0_Final.pdf
  38. S-100 timelines explained - Admiralty, https://www.admiralty.co.uk/news/s-100-timelines-explained
  39. S-100: Next Generation Maritime Products and Services, https://www.hydro.gov.au/charts/s-100
  40. Ecdis Basics | PDF - Scribd, https://www.scribd.com/document/649119951/Ecdis-Basics
  41. Report on Maritime, Inland Waterways, Fisheries and Aquaculture, https://www.euspa.europa.eu/sites/default/files/report_on_maritime_user_needs_and_requirements.pdf
  42. Report on Maritime and Inland Waterways User Needs and, https://www.euspa.europa.eu/sites/default/files/documents/Report_on_User_Needs_and_Requirements_Maritime.pdf
  43. GPS, Galileo, GLONASS, BeiDou and NavIC: GNSS and Location, https://safeguard.sh/resources/blog/gps-and-gnss-evolution-and-location-privacy
  44. GNSS and Secure SATCOM User Technology Report, https://www.euspa.europa.eu/sites/default/files/documents/GNSS_Secure_SATCOM_User_Tech_Report.pdf
  45. Galileo Open Service Navigation Message Authentication (OSNMA), https://www.gsc-europa.eu/galileo/services/galileo-open-service-navigation-message-authentication-osnma
  46. GNSS User Needs in Maritime Sector | PDF | Navigation - Scribd, https://www.scribd.com/document/479858466/Report-on-User-Needs-and-Requirements-Maritime
  47. EGNOS Performance Based on IMO Res. A.1046 (27) - ResearchGate, https://www.researchgate.net/publication/337659250_SBAS_Guidelines_for_Shipborne_Receiver_EGNOS_Performance_Based_on_IMO_Res_A1046_27
  48. EGNOS 1046 Maritime Service Assessment - PMC - NIH, https://pmc.ncbi.nlm.nih.gov/articles/PMC6983232/
  49. Assuring Positioning, Navigation and Timing: Understanding GPS, https://blog.viavisolutions.com/2026/05/20/assuring-positioning-navigation-and-timing-understanding-gps-gnss-attacks-and-mitigation-solutions/
  50. (PDF) Satellite Navigation Signal Authentication in GNSS: A Survey, https://www.researchgate.net/publication/369062786_Satellite_Navigation_Signal_Authentication_in_GNSS_A_Survey_on_Technology_Evolution_Status_and_Perspective_for_BDS
  51. Galileo Open Service Navigation Message Authentication adds, https://www.euspa.europa.eu/newsroom-events/news/galileo-open-service-navigation-message-authentication-adds-another-layer
  52. Galileo OSNMA: One Year as Operational Service - Eurowaypoint, https://eurowaypoint.com/galileo-osnma-one-year-operational-service/
  53. Galileo PRS service as an essential element of resilient PNT - GMV, https://www.gmv.com/sites/default/files/content/file/2024/01/25/114/gmv_news_88_0.pdf
  54. ION Technical Content - The Institute of Navigation, https://www.ion.org/publications/browse.cfm?proceedingsID=171
  55. FE-700 - Marinsat Marine Electronics, https://www.marinsat.com/en/file/furuno-fe700-echosounder-operator-s-manual
  56. BR 45 (3) - Change 1 | PDF | Ionosphere | Navigation - Scribd, https://www.scribd.com/document/713757798/BR-45-3-Change-1
  57. Electromagnetic Log EML900 - YDK Technologies, https://www.ydktechs.co.jp/en/product/pdf/EML900series_catalog.E.pdf
  58. WorkHorse Technical Manual - MOIST, http://www.moist.it/doc/RDI%20WorkHorse%20-%20Manual.pdf
  59. Electronic Navigation Systems - Aeronautical Engineering, https://soaneemrana.org/onewebmedia/ELECTRONICS%20NAVIGATION%20SYSTEM%20BY%20LAURIE..pdf
  60. Speed Log JLN-900|JRC(Japan Radio Co.,Ltd.), https://www.jrc.co.jp/en/product/jln900
  61. ExplorerDVL Operation Manual - Teledyne Marine, https://www.teledynemarine.com/en-us/support/SiteAssets/RDI/Manuals%20and%20Guides/Explorer%20DVL/Explorer_Operation_Manual.pdf
  62. SAL T2/T2+ Speed Log System Manual | PDF | Holography - Scribd, https://www.scribd.com/document/866401108/702270L1-SAL-T2-and-T2-Manual
  63. jln-900 speed log installation and instruction manual, https://alphatronmarine.com/files/secured/docuware_documents/130-LogDop+JRC+JLN-900+InstallOper+Manual++1-11-2022.pdf
  64. Speed log - Alphatron Marine, https://alphatronmarine.com/files/secured/docuware_documents/130-LogDop+JRC+JLN-900+-+Brochure++12-03-2021.pdf
  65. Application Note INS+DVL Calibration MU DVLINS An 001 J - Scribd, https://www.scribd.com/document/1000069837/Application-Note-INS-DVL-Calibration-MU-DVLINS-an-001-J
  66. Tasman DVL Guide - Teledyne Marine, https://www.teledynemarine.com/en-us/support/SiteAssets/RDI/Manuals%20and%20Guides/Tasman/Tasman_DVL_Guide.pdf
  67. Measuring Discharge with Acoustic Doppler Current Profilers from a, https://pubs.usgs.gov/tm/3a22/pdf/tm3a22.pdf
  68. Marine Speed Log Calibration Procedure: The Sea Trial Steps That, https://www.saiyangmarine.com/info/marine-speed-log-calibration-procedure-the-se-103688162.html
  69. JAN-7201/9201 7201/9201 - Alphatron Marine, https://alphatronmarine.com/files/secured/docuware_documents/190-ECDIS+JRC+JAN-7201-9201+Instruction+Manual+TCS+PT500A+PT900+29-08-2021.pdf
  70. SYNAPSIS System Manual - Anschuetz, https://www.anschuetz.com/fileadmin/user_upload/Anschuetz/Approvals/operation_manuals/synapsis_system_manual/4452_SYNAPSIS_System_Manual.pdf
  71. OPERATOR'S MANUAL - Furuno USA, https://www.furunousa.com/-/media/sites/furuno/document_library/documents/manuals/public_manuals/fmd3100_operators_manual.pdf
  72. (PDF) The on-board maritime PNT Module – Concept and, https://www.researchgate.net/publication/259895370_The_on-board_maritime_PNT_Module_-_Concept_and_preliminary_experimental_results
  73. eGlobe G2 Setup & Maintenance Guide - Scribd, https://www.scribd.com/document/962244269/eGlobe-G2-Installation-Setup-and-Maintenance-Manual-rev-2-0-8-eGlobe-2-1-x-JUL-2022
  74. JLN-740A/740N JLN-741A/741N - JRC World, https://www.jrc-world.com/files/secured/docuware_documents/130-LogDop+JRC+JLN-740-741+Instruction+Manual++1-9-2024.pdf
  75. FURUNO FE-700 Echo Sounder Manual - Scribd, https://www.scribd.com/document/945754360/ECHO-SOUNDER-furuno
  76. RESOLUTION MSC.96(72) (adopted on 22 May 2000) ADOPTION, https://wwwcdn.imo.org/localresources/en/KnowledgeCentre/IndexofIMOResolutions/MSCResolutions/MSC.96(72).pdf
  77. 824(19) Performance standards for devices to indicate speed and, https://puc.overheid.nl/nsi/doc/PUC_2511_14/1/