Part 1: System cardDel 1: Systemkort
1. Core Function
Submerged hydraulically driven deepwell pumps install vertically inside each segregated cargo tank, eliminating central pump rooms and cross-tank suction piping1. Driven by pressurized oil from a central hydraulic power unit, each single-stage centrifugal pump independently discharges its assigned tank3. This dedicated architecture enables simultaneous, contamination-free discharge of incompatible chemical or oil grades1. Integrated air or nitrogen stripping and optional suction-well superstripping clear risers and tank sumps to minimal heel, meeting strict marine stripping limits1.
2. Primary Operational Tasks
- Individual tank cargo discharge: Unloads segregated liquid parcels independently or in parallel with stepless hydraulic speed control across varying cargo viscosities and specific gravities1.
- Efficient tank stripping to minimal heel: Evacuates vertical cargo risers via air or nitrogen stack blowing and empties suction wells via optional ejector-driven superstripping lines1.
- Closed-loop cargo heating and circulation: Circulates viscous or temperature-sensitive cargoes through deck-mounted welded plate heat exchangers, supporting coil-free flush tank floors1.
- Tank cleaning evacuation and pump flushing: Matches outflow to tank-cleaning machine inflow to maintain suction-well submergence and performs closed-valve self-cleaning cycles10.
- Hazardous-zone operation without in-tank electrical drives: Uses oil-cooled hydraulic motors inside atmospheric cofferdams—described in OEM brochures as 100% explosion proof for hazardous areas—to avoid submerged electrical components and heat buildup1.
3. System Interconnections
Inputs: High-pressure hydraulic supply oil comes from the central electro-hydraulic or diesel-hydraulic Power Pack (HPU), operating around 150–267 bar (320 bar design) with 2–6 bar continuous jockey-pump pressure when idle6. Pneumatic purge air or nitrogen enters via deck quick-couplings for cofferdam testing (protected by a 3–3.5 bar relief valve) and riser stripping (2–4 bar nominal, or 6–7 bar on higher-head setups)3. Control and monitoring feeds include Cargo Control Room (CCR) PLC stepless speed commands to top-plate Speed Torque Control (STC) valves, three-level tank temperature probes (upper, mid, bottom), top-plate and manifold cargo pressure monitoring, and local motor-pressure and HPU dirty-filter indicators3. Automated downhole cargo-pressure transmitters inside individual tanks are not specified in the reviewed OEM documentation.
Outputs: Pressurized cargo flows up the riser to deck manifolds or through deck-mounted cargo heaters for closed-loop tank circulation1. Low-pressure hydraulic return oil (10–16 bar design rating; approximately 4 bar operating per practitioner commentary) returns to HPU full-flow filtration, seawater coolers, and the system tank4. Cofferdam purge exhaust and seal leakage discharge through the vertical check pipe to a deck exhaust trap for manual volumetric measurement1. The CCR panel monitors and regulates HPU load sharing, cooling-water control valves, active pump controls, and multi-level cargo temperatures, while motor pressures and filter-clogging buttons are checked locally3.
4. Redundancy & Criticality
Under the International Bulk Chemical (IBC) Code (Chapter 3, Sections 3.1.3–3.1.4), cargoes that react hazardously with other products must be isolated by cofferdams, void spaces, pump-rooms, empty tanks, or compatible cargoes, and served by completely separate pumping, piping, and venting systems that do not traverse tanks containing incompatible cargoes unless encased in a tunnel7. Chapter 5 further governs cargo piping scantlings, arrangements, pressure testing, and transfer control systems19. Placing one submerged hydraulic deepwell pump inside each tank satisfies strict physical grade segregation while avoiding operational in-tank pipe blanks prohibited by Section 3.1.41.
Under SOLAS Chapter II-2 Regulation 4.5.10 (and IACS Unified Interpretation SC 307), cargo pump-rooms handling flammable products with flashpoints at or below 60 °C require continuous hydrocarbon gas monitoring (alarming at or below 10% LFL across the pump-room, CCR, ECR, and bridge), bilge level alarms, and fixed CO₂ extinguishing systems under Regulation 10.9.1.121. Submerged hydraulic deepwell installations eliminate the enclosed cargo pump-room entirely, maximizing cargo volume and removing pump-room gas-accumulation hazards1. While the reviewed statutory and OEM texts do not specifically cite IEC Zone 0 electrical classifications or formal intrinsic-safety certifications, vendor brochures state that hydraulic drives eliminate electrical motors and heat buildup inside hazardous cargo spaces1. System redundancy relies on multiple parallel HPU power packs with automated load sharing, a continuous 24/7 jockey pump, and a portable hydraulically driven backup pump (such as a Framo TK80) deployed through deck hatches via extension hoses connected to the hydraulic ring line6.
Part 2: Technical deep diveDel 2: Teknisk dybdeanalyse
1. Deepwell Pump Architecture & Concentric Pipe Stack
A Framo-type submerged deepwell cargo pump is a vertical, single-stage, single-suction, axially balanced centrifugal pump suspended from a top cover plate bolted onto a deck trunk welded into the weather deck1. By locating the impeller inside a tank suction well at the tank bottom, the architecture eliminates horizontal suction headers and dedicated cargo pump-rooms1. Depending on tank depth—ranging across 10 m to 20 m manual specifications, such as the approximately 13 m units on the 21,000 DWT chemical/oil tanker M/T Ruby-T—the vertical pipe stack is stabilized laterally by intermediate support brackets along its length6.
Material selection is partitioned between high-pressure hydraulic containment, low-pressure oil return, and chemical cargo exposure. Across OEM piping specifications, deck-mounted high-pressure hydraulic branch lines and pilot control lines are fabricated from Duplex stainless steel, whereas low-pressure hydraulic return headers and small-bore stripping and slop lines use AISI 316L stainless steel1. Hydraulic lines feature smooth internal surfaces and extensive cold bending to limit flanged joints and maintain oil cleanliness11. For the submerged wetted pump assembly, standard stainless steel construction (such as EN 1.4432 casings with CF3M+Mo impellers on M/T Ruby-T) is joined by super-austenitic 254SMO in Framo's corrosive-duty FPSO hull-pump specifications2. Internally, the short drive shaft (EN 1.6582 alloy steel on M/T Ruby-T) remains isolated from cargo inside an oil-filled housing3.
Within the vertical pipe stack, Framo systems segregate hydraulic and cargo circuits using a nested concentric arrangement alongside dedicated cargo risers1. The high-pressure hydraulic supply pipe runs concentrically inside the low-pressure hydraulic return oil pipe1. This concentric containment ensures that high-pressure supply piping is enveloped by the low-pressure return stream and separated from surrounding cargo by an atmospheric cofferdam pipe extending from the pump head to the top cover plate, while the parallel cargo discharge riser, cargo stripping pipe, and optional superstripping pipe run alongside within the pipe-stack assembly1.
At the base of the stack, a compact hydraulic motor sits inside the lower casing surrounded by low-pressure hydraulic return oil2. A short, stiff independent shaft couples the motor directly to the end-suction impeller, with motor internals and shaft bearings continuously cooled and lubricated by the circulating hydraulic drive oil1. Replaceable wear rings sit between the impeller and volute casing3, and practitioner notes report that newer Framo pump heads incorporate stripping cones to funnel residual liquid into the impeller eye15. Marine practitioner commentary also notes that Framo impellers are secured with a disposable nylon locking bolt and washer—providing higher friction retention than stainless steel fasteners to prevent loose-impeller spark hazards15. An integrated anti-rotation brake (backstop unit) prevents reverse rotation so cargo can be loaded directly down through the pump riser, subject to a maximum top-plate loading pressure of 8 bar, initial tank branch velocity limits of 1 m/s, and minimum valve opening times of 10 s to 45 s depending on pipe diameter to prevent pressure surges3.
System Element / Model | Application & Status | Rated Capacity / Head | Hydraulic Drive Demand | Key Materials & Physical Data |
|---|---|---|---|---|
Framo SD-150 (12 units)6 | M/T Ruby-T (21,000 DWT Chemical/Oil Tanker)6 | 380 m³/h at 110 m.l.c. (SG 0.8, 1.0 cSt)6 | 322 l/min at 243 bar per pump (1,288 l/min at 267 bar for 4 simultaneous)6 | Length ~13 m; Casing EN 1.4432; Impeller CF3M+Mo; Shaft EN 1.65826 |
Framo SD-100 (2 units)6 | M/T Ruby-T Auxiliary Cargo Pumps6 | 240 m³/h (or 120 / 250 m³/h per hydraulic setting) at 110 m.l.c.6 | 109–223 l/min per pump (238 l/min combined for 2 units) at 228–267 bar6 | Paired with DN 25/50 AISI 316L stripping lines & DN 100 slop lines6 |
Framo SD-125 / SD-20027 | Commercial Product & Chemical Tankers27 | 220 m³/h (SD-125) / 500 m³/h (SD-200)27 | 320 bar HP design rating on standard SD series12 | Deck HP/pilot lines: Duplex SS; Deck LP return lines: AISI 316L1 |
Generic 20 m SD Pump24 | OEM Service Manual Baseline24 | Speed: 430 RPM24 | 320 bar HP design; 10–16 bar LP return; 7–10 bar cofferdam design24 | Internal oil volume: 160–165 L (vs. 50 L in 10 m pump)24 |
Framo TK80 (Portable)6 | Emergency Cargo Backup6 | 70 m³/h at 70 m.l.c. (90 m³/h in EMS practitioner notes)6 | 72–85 l/min at 280 bar (or 140 l/min at 180 bar per practitioner notes)6 | Deployed via deck hatch with 25 m DN 100 cargo hose & two 18 m hyd. hoses6 |
2. Double-Barrier Shaft Sealing & Cofferdam Purging
A critical architectural distinction separates Framo-type submerged deepwell pumps from competing deepwell designs regarding how the shaft seal stack prevents cargo-to-oil cross-contamination. Whereas alternative deepwell designs—such as Hyundai submerged pumps and Japanese deepwell models referenced in manuals and shipboard comparisons—employ mechanical seals on the cargo side15, official Framo manuals and brochures specify a three-part double-barrier arrangement consisting of a mechanical oil seal on the hydraulic side, a single cofferdam lip seal, and a double cargo lip seal1. Shipboard practitioner commentary identifies the cargo and cofferdam lip seals as PTFE (Teflon) sealing rings riding on a replaceable, polishable ceramic shaft sleeve15.
This asymmetric seal selection addresses two hazardous-zone operating demands simultaneously. First, because the hydraulic motor chamber sits inside the cofferdam and is surrounded only by low-pressure return oil (10–16 bar design; around 4 bar operating per practitioner notes), the mechanical oil seal running in clean, cooled ISO 46 hydraulic oil achieves a service life around 10,000 running hours under normal conditions12. Second, the lower double cargo lip seal is isolated from pump discharge pressure and exposed only to static cargo tank head1. According to practitioner comparisons, PTFE double lip seals tolerate momentary dry operation during final tank stripping without generating the frictional overheating associated with dry-running mechanical cargo seals15.
Between the mechanical oil seal and the double cargo lip seal lies an atmospheric dry cofferdam chamber connected via the cofferdam pipe to a check pipe and exhaust trap on the top cover plate1. Unlike deepwell systems that maintain continuous fixed-line air or nitrogen pressure inside the cofferdam—an arrangement practitioner commentary warns can allow dense, free-flowing cargoes such as sulfuric acid to migrate back into fixed shipboard air lines if seals fail—standard Framo cargo pumps keep the cofferdam ventilated at atmospheric pressure and rely on periodic deck-level purging8.
Routine cofferdam purging is the sole non-intrusive method to monitor shaft seal integrity without entering cargo tanks34. OEM service bulletins and manuals direct crews to purge the cofferdam before and after operating each cargo pump (and daily or more frequently if leakage rises)3:
- Preparation and safety verification: Position a suitable catch container beneath the deck exhaust trap, verify that the trap drain valve is clear of residue (rodding with a pin if clogged) and closed, drain condensed water from the air or nitrogen supply line, and wear chemical safety gear before venting potentially hazardous vapors or liquids3.
- Gas connection and pressure protection: Attach the flexible hose with snap-on coupling to the cofferdam purging connection on the pump top cover plate3. Purging pressure is limited by a 3–3.5 bar relief valve fitted at the purging port to protect the pump seals from overpressure3.
- Purging and flow confirmation: Open the air or inert-gas valve (max consumption 0.3 Nm³ on a 10 m pump to 1.0 Nm³ on a 20 m pump) and confirm that purge gas exits the exhaust trap vent line, verifying that the cofferdam passage is open3.
- Sequential draining and logging: Purge the cofferdam in several short sequences, draining the exhaust trap into the container between sequences, then disconnect the gas supply, close the exhaust trap drain valve, and record recovered fluid volumes strictly in liters for trend logging and OEM submission3.
A small mist or leak from the 3–3.5 bar relief valve while liquid is displaced is normal, whereas full relief lifting with zero gas exiting the exhaust trap indicates a blocked cofferdam3. Because a blocked cofferdam prevents leak detection and traps corrosive cargo against the hydraulic seal, practitioner guidance emphasizes that a cargo pump with a blocked cofferdam must never be operated15.
Observation in Exhaust Trap | Probable Root Cause | Verification & Corrective Action |
|---|---|---|
Cargo liquid collected during purge15 | Wear or damage on double cargo lip seal, scored ceramic sleeve, or pump-head gasket leak15 | Stand sample to separate and measure volume; official OEM bulletin SB-47 lists no fixed numerical leakage cutoff (requiring OEM review of submitted logs), though shipboard practitioner commentary views up to ~400 ml/day during full-day pumping as tolerable15. Practitioner notes recommend pressure-testing the cofferdam at ~3 bar with a rubber-blanked relief valve and soap water, and changing cofferdam and double cargo lip seals together15. |
Hydraulic oil collected during purge15 | Mechanical oil seal wear, shaft seal failure, or internal pipe-stack/pump-head oil leak15 | Practitioner commentary advises pressurizing the hydraulic return line to verify oil-side leakage and treats up to ~200 ml/day as benign15. If oil leakage becomes excessive, close hydraulic valves, deploy the portable TK80 pump, and split/pressure-test the pump for repair15. |
No gas exits trap; 3–3.5 bar relief valve lifts3 | Cofferdam annular space or check pipe blocked by solidified or crystallized cargo15 | Shut down pump immediately15. OEM purging instructions recommend hot-water circulation (for phenol/caustic soda) or fresh-water flushing (after acids), while practitioner notes describe steam or solvent clearing before restarting15. |
3. Central Hydraulic Power Pack (HPU) & Proportional Control
Powering all submerged cargo pumps, ballast pumps, tank cleaning pumps, and auxiliary deck consumers from a central hydraulic ring line enables shipyards to size prime movers for simultaneous fleet discharge envelopes rather than the sum of individual tank maxima4. On small and medium tankers, the HPU uses electric motor-driven variable-displacement hydraulic power packs; on medium and large tankers with higher discharge heads, electric packs (matched to economical sea-going auxiliary generator loads) combine with diesel-driven hydraulic power packs to cover heavy port unloading loads1. Each variable-displacement hydraulic pump incorporates a pulsation damper and sits on resilient mounts alongside cold-bent stainless piping with resilient pipe clamps to minimize structure-borne vibration and noise11.
On the 21,000 DWT chemical/oil tanker M/T Ruby-T, the central HPU integrates three electric A4V355 variable-displacement axial-piston power packs rated at 270 kW each (440 V, 60 Hz, 3-phase, IP55, 95.5% efficiency, 430 A normal current), delivering 535 l/min each for a combined capacity of 1,605 l/min at 267 bar6. This covers the vessel's simultaneous design discharge case of four SD-150 pumps (1,288 l/min) plus two SD-100 pumps (238 l/min)—totaling 1,760 m³/h of cargo flow on 1,526 l/min of hydraulic oil—leaving a 79 l/min (approximately 4.9%) reserve margin6.
A Programmable Logic Controller (PLC) inside the Framo control panel governs system logic, incorporating a power-saving load-sharing device that automatically regulates and balances load (via motor current or swashplate angle per practitioner notes) across active power packs11. To minimize throttling losses, noise, energy draw, and component wear, OEM operating manuals instruct operators to keep main hydraulic system pressure at a maximum of 15 bar above the highest-loaded cargo pump consumer (ΔP ≤ 15 bar)3. During parallel pumping of multiple tanks, optimal efficiency is achieved by placing individual cargo pump controllers toward maximum and throttling discharge capacity centrally via the main hydraulic system pressure—running as many pumps in parallel at reduced hydraulic pressure as practical rather than fewer pumps near maximum pressure10.
HPU Subsystem / Parameter | M/T Ruby-T System Data | OEM Operational Standards & Control Logic |
|---|---|---|
System Oil Volume & Grade | ~6.5 m³ (excluding storage/drain tanks)6 | ISO 46 mineral hydraulic oil (flashpoint 180–230 °C; avoid heated surfaces >60 °C)4. |
Return-Line Filtration | Full-flow return filter; 1.3 kW oil transfer pump6 | Max particle contamination: code 16/12 (referencing the 1999 6 µm(c)/14 µm(c) revision)14. Refill solely via transfer unit/filter box; replace genuine Framo elements if red dirty-filter button pops >30 °C4. |
Oil Cooling & Ventilation | 1 × 238 kW SW cooler (70 m³/h SW at 36 °C inlet); 41 kW room heat dissipation (3.72 m³/s ventilation)6 | PLC modulates seawater cooling inlet valve to regulate oil temperature13. If oil <20 °C, circulate at max 100 bar to warm before discharge10. |
Jockey / Feed Pump | 1 × 2.6 kW continuous jockey pump6 | Holds 2–6 bar positive pressure on idle lines to prevent air, moisture, or cargo ingress; runs continuously per practitioner commentary for venting/filtration6. |
Operating Pressure Envelope | 267 bar design operating; 228–243 bar nominal pump demand6 | Startup against closed cargo valve: 40–50 bar for 1–2 min3; standard discharge: ~150 bar upward10; minimum limit: ≥50 bar per practitioner notes15; heating mode (main packs): 50–60 bar10. |
Individual cargo pump capacity and speed are controlled steplessly from the CCR panel or locally at the deck trunk via a Speed Torque Control (STC) valve mounted on each pump's top cover plate (which replaced older Flow Control Valves on modern builds per practitioner commentary)1. Acting as the system's proportional flow and torque regulator, the STC valve automatically modulates hydraulic oil pressure and flow supplied to the submerged hydraulic motor up to a factory-calibrated, tamper-sealed ceiling1. As a result, the drive cannot overload or overspeed even when handling dense or viscous cargoes1.
4. Tank Stripping Sequence & Super-Stripping
MARPOL Annex II Regulation 12 progressively tightened allowable cargo-residue limits for chemical tankers carrying Noxious Liquid Substances (NLS) in bulk38. Ships built before 1 July 1986 were limited to 300 L (Categories X and Y) and 900 L (Category Z), reduced to 100 L (X/Y) and 300 L (Z) for vessels built from 1 July 1986 onward (subject to a 50 L water-test tolerance)39. For every ship constructed on or after 1 January 2007, Regulation 12 requires that each tank certified for Category X, Y, or Z substances retain no more than 75 L (0.075 m³) across the tank, pump, and associated piping up to the manifold—with zero tolerance permitted9. Compliance is verified under Appendix 5 water performance tests at prescribed favorable trim and list limits against at least 100 kPa (1 bar) of unloading manifold backpressure40. Satisfying this sub-75 L stripping limit allows non-solidifying, low-viscosity Category Y and Z cargoes to avoid mandatory in-port prewashing to shore reception facilities41.
Submerged deepwell pumps clear their vertical risers through pressurized air or nitrogen blowing while operating the impeller against a closed main discharge valve1. Rather than installing mechanical flap non-return valves above the impeller—which practitioner commentary notes obstruct clearing of suction-pit sediments on competing designs—the continuously spinning centrifugal impeller generates hydrodynamic head at the volute base, acting as a dynamic non-return barrier so purge gas cannot force cargo back into the tank1.
Standard OEM and shipboard stripping proceeds through the following sequence:
- Pressure reduction at suction loss: At the end of discharging or when incipient cavitation triggers pump vibration and hydraulic pressure pulsations, reduce the pump's hydraulic pressure to approximately 100 bar (throttling the cargo discharge valve slightly if it improves stripping)10.
- Main valve closure and backpressure relief: Once the tank is empty, close the main cargo discharge valve and stop the pump10. Purge the deck cargo line, close the manifold valve, and relieve deck line pressure to minimize manifold backpressure10.
- Closed-discharge startup: Open the small-bore stripping ball valve (such as the DN 25 or DN 50 AISI 316L bypass line on M/T Ruby-T) and restart the pump locally at reduced hydraulic pressure against the closed main discharge valve—approximately 80–100 bar per OEM manuals, or down to 50 bar in shipboard handbook notes (never operating below 50 bar)6.
- Slow purge-gas admission: Connect compressed air or nitrogen to the cargo-pipe purge coupling on the pump top plate, opening the valve slowly (critical with dense liquids such as sulfuric acid to avoid liquid hammer and PTFE gasket creep per practitioner warnings)10. Set purge gas pressure to 1 bar plus static riser height—normally 2–4 bar in OEM procedures, or 6–7 bar on higher-head setups like M/T Ruby-T6.
- Stack evacuation and endpoint detection: Purge gas pushes the cargo column out through the small-bore stripping line into the deck cargo line (or to a slop/residue tank via internal stripping when manifold backpressure is high)1. Completion is recognized by frequent speed variations (racing) of the pump once gas clears the stack; closing purge gas briefly during high-speed racing shortens stripping time10. Repeat two to three short sequences if needed before closing the stripping valve, stopping the pump, and purging the cofferdam6.
Where ultra-low tank heel is required, an optional superstripping (vacuum drain) pipe extends from the bottom of the suction well to the main deck1. Connected via snap-on couplings to an air- or nitrogen-driven ejector discharging into the main stripping line, superstripping evacuates residual suction-well liquid in roughly 2 minutes on M/T Ruby-T, yielding a combined stripping cycle of approximately 5 minutes per tank1. Practitioner commentary notes that pairing this layout with stripping cones reduces remaining on-board residue inside the pump well to under 1 L15. Where Framo deck-mounted welded plate cargo heaters replace internal heating coils, the resulting flush tank top further accelerates drainage and cleaning1—though individual vessels such as M/T Ruby-T may also retain localized AISI 316L bottom coils around the suction well alongside deck heaters6.
Regulatory / Operational Benchmark | Standard / Vessel Data | Key Conditions & Consumption |
|---|---|---|
MARPOL Annex II (Pre-1 Jul 1986)39 | ≤300 L (Cat X, Y); ≤900 L (Cat Z)39 | 50 L tolerance permitted on Reg. 12.1/12.2 water test39 |
MARPOL Annex II (≥1 Jul 1986 – 31 Dec 2006)39 | ≤100 L (Cat X, Y); ≤300 L (Cat Z)39 | Appendix 5 water test at favorable trim/list and ≥100 kPa manifold backpressure39 |
MARPOL Annex II (≥1 Jan 2007)9 | ≤75 L (0.075 m³) across Cat X, Y, and Z9 | Zero tolerance (50 L tolerance explicitly prohibited)9 |
M/T Ruby-T Stack Stripping6 | ~3 min per tank; 6–7 bar air/N₂6 | 1.2 Nm³/sequence (SD-150, 2–3 max); 0.5 Nm³/sequence (SD-100)6 |
M/T Ruby-T Superstripping6 | ~2 min per tank (~5 min total combined)6 | Suction-well pipe evacuated via air/N₂ ejector to main stripping line6 |
5. Failure Modes, Viscosity Limits & Maintenance
Because hydraulic motors deliver full torque across their entire speed range without electrical thermal-winding constraints, Framo product literature states the pumps face no limitation on cargo specific gravity (covering SG 0.8–1.8) and handle viscosities up to 850 cSt and heavy molasses1. On M/T Ruby-T, for instance, the baseline viscous design cargo is Heavy Fuel Oil at 370 cSt (55 °C, 950 kg/m³)6. Beyond normal hydraulic capacity limits, operational reliability hinges on mitigating dry running, cargo solidification or crystallization, vapor flashing, and hydraulic oil degradation.
Dry-running and tank-cleaning imbalance: Extended dry running strips away fluid cooling and damping at the impeller wear rings and cargo lip seals, causing pump vibration, hydraulic pressure hunting, and accelerated seal/sleeve wear3. Shipboard practitioner guidelines warn against dry running or steaming the cargo stack for more than 10 minutes15. During tank washing, operators must balance pump hydraulic pressure to match tank-cleaning machine inflow so the suction well stays submerged, followed by a 1–2 minute self-cleaning run at approximately 110 bar against a closed discharge valve and fresh-water flushing whenever seawater has been used10.
Solidification, viscosity spikes, and crystallizing cargoes: Temperature-sensitive viscous cargoes such as palm oils and heavy fuel oils lose roughly 1–2 °C per 24 hours passively and typically require reheating at 4–6 °C per 24 hours prior to arrival (such as M/T Ruby-T's 200 kW thermal-oil deck heaters maintaining 370 cSt HFO at 66 °C against 0 °C seawater and -10 °C air)5. To prevent overheating or carbonizing product on heater plates, the cargo pump must circulate cargo before the heating medium valve opens, and heating medium must shut off before stopping the pump10. Operators must never heat and discharge simultaneously (or cargo recirculates through the heater back into the tank), and must never clean stainless deck heaters with seawater above 60 °C due to severe chloride corrosion sensitivity10. For crystallizing or viscous residues that threaten to clog the cofferdam—such as phenol, caustic soda, and molasses—OEM purging procedures recommend circulating hot water through the cofferdam (phenol/caustic) or flushing with fresh water (acids), while practitioner notes describe reverse-filling the cofferdam with water when discharging molasses15. The reviewed technical manuals do not specify operating data or wear tolerances for molten elemental sulfur or abrasive solid slurries, though practitioner notes do highlight liquid-hammer and PTFE gasket-creep hazards during air stripping of dense sulfuric acid15.
Cavitation with high-vapor-pressure cargoes: While explicit NPSH curves are not included in the reviewed manuals, Framo brochures note that continuous cooling of the submerged hydraulic motor assembly by circulating hydraulic oil prevents heat buildup into volatile or heat-sensitive cargoes1. Submerging the single-stage impeller inside the bottom suction well maximizes static head, and reducing hydraulic motor speed (around 100 bar) mitigates vortexing and air suction as tank levels drop10. Highly volatile or reactive cargoes such as propylene oxide and isoprene must not be circulated outside their cargo tanks through external deck heaters1.
Hydraulic oil overheating, aeration, and piping fatigue: Exceeding the 15 bar HPU consumer pressure margin, fouling seawater oil coolers, or loading cold oil (<20 °C) above 100 bar accelerates oil oxidation and component wear, while particle contamination above code 16/12 damages axial-piston pumps and motors10. Practitioner commentary notes that air trapped after maintenance causes pressure-line shock ("air bubble smashing") and expansion leaks at return joints on older ships, requiring strict venting at control assemblies, service valves, and high points14. Any external mineral-oil leakage contacting hot surfaces above 60 °C creates a fire hazard given its 180–230 °C flashpoint4.
Maintenance split and deck-mounted extraction: Routine wear-and-tear replacements—including impeller wear rings, polishing ceramic sleeves, and changing the cofferdam lip seal and double cargo lip seal together per manufacturer recommendation—are performed from inside the gas-freed cargo tank without disturbing the hydraulic motor section1. By contrast, hydraulic oil leaks caused by internal pipe-stack fatigue cracks (driven by prolonged abnormal vibration) or worn oil-lubricated shaft bearings and mechanical oil seals require isolating the pump, disconnecting deck-trunk flanges, and extracting the complete pump assembly onto the deck using a shore or deck crane for splitting and pressure testing3. OEM mounting instructions stress slow, controlled hoisting with approved lifting gear to avoid shock damage to motor bearings, followed by strict cleanliness, component pressure testing, and high-point air venting before restarting4.
Failure Mode / Hazard | Root Mechanism | Operational Safeguard / Maintenance Action |
|---|---|---|
Dry-running / Wear-ring & lip-seal damage3 | Loss of suction submergence during stripping or tank washing10 | Limit dry/steam operation to <10 min (practitioner rule); balance outflow to tank-washing inflow; drop drive pressure to ~100 bar on hunting10. |
Cargo solidification / Cofferdam clogging5 | Cooling of palm oil/HFO; crystallization of phenol, caustic, or molasses5 | Circulate cargo before opening heater; never heat static cargo; flush cofferdam with hot water (phenol/caustic) or fill with water (molasses)10. |
Vapor flashing / Vortex hunting1 | High-vapor-pressure cargoes or low suction-well submergence1 | Rely on suction-well static head and oil-cooled motor housing; lower hydraulic speed on hunting; never circulate PO or isoprene externally1. |
HPU oil contamination / Startup shock4 | Particulate ingress (>code 16/12), trapped air/water, or >15 bar ΔP10 | Fill only via transfer filter box; inspect dirty-filter button >30 °C; vent high points after repair; hold 2–6 bar idle jockey pressure4. |
Internal hydraulic motor / Bearing / Stack fault15 | Bearing wear (>10,000 h) or vibration-induced pipe-stack crack15 | Isolate hydraulic valves, deploy portable TK80 pump mid-voyage, and extract full assembly via deck trunk with crane for splitting/pressure testing15. |
References
- Framo Cargo Pumping System, https://gkunicom.ru/upload/iblock/6e2/6e219293b9f9a7c7c083e8c3b7a8fa36.pdf
- Floating production storage and offloading - Framo, https://www.framo.com/media/dmrp50xc/framo-fpso-submerged-pumping-system.pdf
- Framo Cargo Pump Operation Manual | PDF - Scribd, https://www.scribd.com/document/267369858/93865793-Framo-Operation-Manual
- Framo Cargo Pumping System Guide | PDF | Pipe (Fluid Conveyance), https://www.scribd.com/doc/50598275/framo
- Framo Cargo Pumping Systems Overview | PDF - Scribd, https://www.scribd.com/document/616142381/Framo-Cargo-Pumping-Systems-Brochure
- 21.000 DWT CHEMICAL/OIL TANKER, https://maritimeexpert.files.wordpress.com/2016/08/pa-manuel.pdf
- 3.1 Cargo segregation - imorules, https://www.imorules.com/GUID-C773D869-1ABD-4A26-A165-A501DF17F743.html
- The Submerged Cargo pump - Framo, https://www.framo.com/cargo-pumping-systems/cargo-pumping/submerged-cargo-pump/
- Revised MARPOL 73/78 Annex II and IBC Code - ClassNK, https://www.classnk.com/hp/pdf/tech_info/tech_img/T655e.pdf
- Service Bulletin - Framo, https://www.framo.com/media/t1jborvm/no10_1993__operation_of_framo_cargo_pumps.pdf
- Hydraulic Drive for Cargo Pumps | Flexible Power Solutions - Framo, https://www.framo.com/cargo-pumping-systems/cargo-pumping/hydraulic-drive/
- Framo Cargo Pump SD100-5 Manual | PDF - Scribd, https://www.scribd.com/document/889307620/1000-0115-4-SD100-5-Service-manual
- HM-1 (E) - Finished Drawing & Instruction Manual For Cargo, https://www.scribd.com/document/481122046/HM-1-E-FINISHED-DRAWING-INSTRUCTION-MANUAL-FOR-CARGO-PUMPING-SYSTEM-VOL-I-pdf
- Hydraulic Oil Filling Procedure | PDF | Valve | Pump - Scribd, https://www.scribd.com/document/857616117/1400-0326-4
- Deepwell Pumps on chemical tankers– Capt Ajit Vadakayil, https://captajitvadakayil.in/2021/02/10/deepwell-pumps-on-chemical-tankers-capt-ajit-vadakayil/
- Framo Portable Cargo Pumps For Chemical Tankers - Scribd, https://www.scribd.com/document/1060216886/Framo-Portable-Cargo-Pumps-for-Chemical-Tankers-Care-and-Storage-Onboard
- Safe Cargo Handling | Framo Cargo Pumps, https://www.framo.com/cargo-pumping-systems/cargo-pumping/safe-operation/
- 02 IBC-Code International code for the construction and equipment, https://puc.overheid.nl/nsi/doc/PUC_2391_14/5/
- IBC Code Overview and Chapter Summaries | PDF | Ships | Cargo, https://www.scribd.com/document/922711021/4-Manvir-Matharu-ASM-Contents-of-Various-Publications
- Chapter 5 Cargo transfer, https://www.imorules.com/IBC_CH5.html
- Technical Information - ClassNK, https://www.classnk.or.jp/hp/pdf/tech_info/tech_img/T462e.pdf
- IACS unified interpretation SC 307 of SOLAS regulation II-2/4.5.10, https://iacs.s3.af-south-1.amazonaws.com/wp-content/uploads/2025/02/07131500/SSE-11-10-2-IACS-unified-interpretation-SC-307-of-SOLAS-regulation-II-24.5.10-regarding-protection-of.-IACS.pdf
- 02 IBC-Code, 2004 International code for the construction and, https://puc.overheid.nl/doc/PUC_2408_14/1/
- Framo Cargo Pump SD200-6 - maritimeexpert.wordpress.com, https://maritimeexpert.files.wordpress.com/2016/08/framo-instruction-and-service-manual.pdf
- Framo Mounting Instructions Overview | PDF | Pump - Scribd, https://www.scribd.com/document/565824870/FRAMO-Mounting-instruction
- Framo Cargo Pumping System Overview | PDF | Oil Tanker - Scribd, https://www.scribd.com/document/419219246/Framo-Cargo-Pumping-System-Brochure
- Significant Ships of 2023 | PDF - Scribd, https://www.scribd.com/document/1033239139/Significant-Ships-of-2023
- Maersk Deck Operating Manual Overview | PDF | Valve - Scribd, https://www.scribd.com/document/367167227/Maersk-Ramsey-Deck-Cargo-pdf
- Framo SD200-6 Pump Maintenance Guide | PDF - Scribd, https://www.scribd.com/document/799440374/1000-0149-4
- Framo Cargo Pump Maintenance Manual | PDF - Scribd, https://www.scribd.com/doc/283007070/Framo-Cargo-Pump-1000-0131-4
- Hyundai Submerged Cargo Pump System | PDF - Scribd, https://www.scribd.com/document/394690058/Hyundai-Pump-SUBMERGED-C-PUMP-pdf
- Service Bulletin - Framo, https://www.framo.com/media/hyddmmpg/no16_1997_framo_submerged_cargo_pump-_pressure_testing_routine.pdf
- marine lubricants handbook, https://www.chevronmarineproducts.com/content/dam/chevron-marine/Brochures/new-active-brochures/Chevron%20Marine%20Lubricants%20Handbook.pdf
- PURGING ROUTINE FOR FRAMO CARGO PUMPING SYSTEM, https://www.framo.com/media/aqibmja1/sb-47-purging-routine.pdf
- Maintenance/upgrading of hydraulic piping system - Framo, https://www.framo.com/media/mowkndnu/sb41_maintenance-and-upgrade-of-hydraulic-piping-system.pdf
- Hydraulic course manual | PDF - Slideshare, https://www.slideshare.net/slideshow/hydraulic-course-manual/29395618
- Tanker Regulations and Cargo Classifications | PDF - Scribd, https://www.scribd.com/document/699980938/CHEMCO-n-Tasco-e-learning
- Annex II - Regulation 12 - MARPOL Training Institute, https://www.marpoltraininginstitute.com/MMSKOREAN/MARPOL/Annex_II/r12.htm
- MARPOL Annex II: Noxious Liquid Regulations | PDF - Scribd, https://www.scribd.com/doc/267074473/MARPOL-Annex-II-Regulations-for-Liquid-Noxious-Substances
- Annex II - Appendix 5 - MARPOL Training Institute, https://www.marpoltraininginstitute.com/MMSKOREAN/MARPOL/Annex_II/app5.htm
- App. 5 - PSC Guidelines for Discharge under MARPOL Annexes I & II, https://risk4sea.com/psc-wiki-risk4sea/appendices/psc-guidelines-for-discharge-under-marpol-annexes-i-ii/
- OCTCO Course Overview and Details | PDF | Oil Tanker - Scribd, https://www.scribd.com/document/786565516/Coral-Octco-Handbook
- MARFLEX Cargo Pump Manual | PDF - Scribd, https://www.scribd.com/document/691978244/76636966-MARFLEX-Cargo-Pump-Manual