Ship Subsystems & EngineeringSkipssystemer og maskinteknikk · Engineering system cardTeknisk systemkort

Oil and Chemical Tanker Inert Gas Systems

An Inert Gas System (IGS) blankets cargo tank ullage spaces with low-oxygen gas (≤5% O₂ by volume at supply) during cargo discharge, crude oil washing, purging, and ballast or sea passages.

min readmin lesing
24
wordsord
5,112

#Inert Gas#IGS#Tankers#Explosion Prevention

Part 1: System cardDel 1: Systemkort

Core Function

An Inert Gas System (IGS) blankets cargo tank ullage spaces with low-oxygen gas (≤5% O₂ by volume at supply) during cargo discharge, crude oil washing, purging, and ballast or sea passages1. By displacing atmospheric air under positive pressure, the system keeps tank atmospheres at ≤8% O₂ by volume—safely below the ~11% O₂ threshold needed to ignite typical petroleum hydrocarbon vapors1. Maintaining this inerted overpressure excludes air ingress and keeps cargo tanks permanently outside the flammable envelope even if electrostatic sparks or other ignition sources occur2.

Primary Operational Tasks

  • Oxygen Displacement & Hydrocarbon Purging: Displace tank air with ≤5% O₂ inert gas to hold cargo tanks at ≤8% O₂ outside the flammable envelope, and purge hydrocarbon vapors below the Critical Dilution Line and Lower Flammable Limit prior to gas-freeing2.
  • Positive Tank Overpressure Maintenance: Continuously regulate deck main pressure (typically 200–1,200 mmWG) during cargo discharge and thermal contraction to prevent atmospheric air from leaking into ullage spaces2.
  • Machinery Space Backflow Prevention: Isolate hazardous cargo vapor spaces from gas-safe machinery rooms using at least two independent non-return barriers capable of withstanding cargo tank test pressure2.
  • Pressure and Vacuum Envelope Protection: Protect tank hull plating against structural overpressure or vacuum collapse using modulating regulating valves, high-velocity P/V valves, mast risers, and a liquid-filled P/V breaker8.
  • Controlled Vapour Venting and Inerting Stabilization: Stabilize gas quality before pumping begins, automatically vent off-spec gas (>5% O₂), and route displaced vapors safely overhead during loading3.

System Interconnections

Inputs

  • Gas, Fuel, and Air Feeds: Main or auxiliary boiler flue-gas uptake—or main/auxiliary engine exhaust combined with a generator in hybrid systems—dedicated burner fuel (MDO/MGO/HFO via dual fuel pumps) plus combustion air for oil-fired Inert Gas Generators (IGGs), or filtered compressed air for hollow-fiber membrane N₂ units3.
  • Seawater Cooling and Sealing Supply: Two independent seawater sources feeding the flue-gas scrubber tower without interfering with essential ship services, plus two separate seawater pumps maintaining continuous Deck Water Seal supply3.
  • Electrical Power Supply: Shipboard electrical power (routed from main distribution/switchboard panels, though specific bus voltages and breaker architectures are not detailed in the cited regulatory texts) driving motor-driven IG blowers, N₂ feed-air compressors, pumps, electric heaters, and automatic control/indicating systems3.
  • Process and Safety Instrumentation: Supply main O₂ analyzers and dual ambient O₂ sensors (<19% O₂) in IGS machinery spaces1, pressure transmitters on the IG main downstream of non-return devices (plus cargo/slop tank pressure monitoring)3, blower outlet temperature sensors, scrubber water flow/level switches, water-seal level sensors, and N₂ suction pressure/temperature and condensate drains3.

Outputs

  • Conditioned Inert Gas: Cooled, scrubbed, demisted combustion gas (≤5% O₂, ≤8°C above seawater in vendor IGG specs, ~100% saturated) or ultra-dry nitrogen (95%–99.9% N₂) routed into the deck IG main3.
  • Acidic Scrubber Effluent: Soot- and SO₂-contaminated, low-pH seawater washwater discharged directly overboard (along with deck seal drains) without routing through machinery spaces3.
  • Automated Valves and Physical Barriers: Gas regulating valve, >5% O₂ atmospheric vent/recirculating valve, Deck Water Seal (or fail-safe double-block-and-bleed), mechanical non-return valve, and power-operated deck isolating valve3.
  • Automatic Trips, Recordings, and Alarms: Blower shutdown and regulating-valve closure on scrubber high water level, low scrubber cooling flow, or high-high IG temperature; regulating-valve closure and atmospheric venting at >5% O₂; continuous low-water-seal alarm (with plant-specific trips where fitted); cargo pump shutdown or independent alarm at very-low IG main pressure; permanent Cargo Control Room (CCR) O₂/pressure recordings; and CCR, Engine Control Room (ECR), and bridge low-pressure alarms (<100 mmWG)1. While Voyage Data Recorders (VDRs) log ship physical status and bridge command/control data under IMO MSC.333(90)23, the cited regulatory texts do not specify direct VDR channel mapping for individual IGS alarms.

Redundancy & Criticality

SOLAS Chapter II-2 Regulations 4.5.5 and 16.3.3 mandate fixed IGS compliance with FSS Code Chapter 15—rewritten under Resolution MSC.367(93) from 1 January 2016 and amended under MSC.457(101) from 1 January 2024—on all oil and chemical tankers of ≥8,000 DWT keel-laid on or after 1 January 2016 carrying cargoes with flashpoint ≤60°C or flammable IBC Code cargoes (regardless of individual tank size or washing machine capacity, though Administrations may accept equivalents for 8,000–19,999 DWT vessels), as well as pre-2016 tankers of ≥20,000 DWT and any crude tanker using Crude Oil Washing (COW)1. Plants must deliver ≥125% of maximum cargo discharge volume via at least two blowers (one blower may be permitted for IGGs if full spares are carried, and chemical tankers may use lower capacity if maximum discharge is capped at ≤80% of IGS capacity) while holding tanks at ≤8% O₂ under positive pressure3. Redundancy relies on dual deck non-return barriers (a continuously supplied Deck Water Seal with two pumps—or fail-safe double-block-and-bleed—followed by a positive-closing non-return valve) plus a 250 mm nominal valved bolted flange downstream of the non-return valve for external inert gas supply3.

Part 2: Technical deep diveDel 2: Teknisk dybdeanalyse

1. Flammability Diagram & Inerting Physics

Hydrocarbon vapor combustion inside a cargo tank occurs only when fuel vapor and oxygen fall within specific concentration boundaries depicted on a ternary hydrocarbon/air/inert-gas composition diagram (ISGOTT Figure 1.1)5. Pure atmospheric air (~21% O₂ and 79% N₂) lies at Point A on the oxygen axis, and any binary mixture of hydrocarbon vapor and air sits along the straight "Air Line" extending from 100% air to 100% hydrocarbon5. Along this Air Line, flame propagation is possible only between the Lower Flammable Limit (LFL) and Upper Flammable Limit (UFL), spanning roughly 1% to 10% hydrocarbon vapor by volume for typical petroleum cargoes, though individual chemical cargoes span much wider limits1.

Substance or Cargo

LFL in Air (% vol)

UFL in Air (% vol)

Limiting Oxygen Concentration in N₂ (% O₂)

Basis in Technical Sources

Petroleum Tanker Hydrocarbon Mixtures

~1.0

~10.0

~11.0

ISGOTT / Industry guidance1

Gasoline

1.2–1.4

7.6

~11.0 (general petroleum band)

Safety tables & petroleum guidance30

Methane (CH₄)

4.4–5.0

15.0–16.4

10.7–11.3 (experimental) / 12.0

CDC/NIOSH & literature tables30

Propane (C₃H₈)

2.0–2.2

9.5–10.1

10.5–10.7 (experimental) / 11.5

CDC/NIOSH & literature tables30

n-Butane (C₄H₁₀)

1.86

8.41

12.0

Literature & engineering tables30

Ethylene (C₂H₄)

2.7–2.75

28.6–36.0

8.5–10.0

CDC/NIOSH & chemical engineering texts29

Hydrogen (H₂)

4.0–5.0

75.0–75.9

4.6–5.0

CDC/NIOSH & literature tables30

Injecting inert gas into a fuel–air mixture shifts the atmosphere away from the Air Line toward the oxygen-depleted region, raising the LFL slightly while driving down the UFL until both limits pinch together at the nose of the shaded flammable region (loop CED in ISGOTT)5. This vertex defines the Limiting Oxygen Concentration (LOC) or Minimum Oxygen Concentration (MOC), below which no hydrocarbon concentration can burn5. Experimental data show LOC values in nitrogen around 10.7%–12.0% O₂ for methane, propane, and butane, supporting ISGOTT's ~11% O₂ petroleum threshold5. Using CO₂ instead of N₂ raises the LOC (for instance, to 14.5% O₂ for methane and propane)33, whereas reactive chemical cargoes such as ethylene (8.5%–10.0% O₂) and hydrogen (4.6%–5.0% O₂) exhibit lower LOCs that demand high-purity nitrogen blanketing29.

Maintaining every cargo tank at ≤8% O₂ with supply gas capped at ≤5% O₂ establishes a deliberate safety buffer below the ~11% O₂ combustion nose to account for incomplete mixing, analyzer error, and minor hatch weeping3. Because inert gas removes oxygen rather than hydrocarbon vapor, keeping tank O₂ below 8% prevents ignition even if an electrostatic discharge or mechanical spark occurs inside a vapor-rich tank2.

Any dilution process traces a straight vector across the flammability diagram: admitting air moves the mixture toward Point A, while injecting inert gas moves it toward the inert supply point on the oxygen axis5. Consequently, an inerted, hydrocarbon-rich tank lying above the Critical Dilution Line (Line GA)—for example, at Point F—cannot be gas-freed directly with air, because the dilution line FA passes squarely through the explosive CED loop5. Operators must therefore purge first with inert gas to pull the mixture below Line GA to Point H (an illustrative training guide puts safe transition near 2% hydrocarbon and 5% O₂) before admitting fresh air to traverse safely toward Point A without crossing the flammable zone5.

2. Flue-Gas Scrubbers vs. Oil-Fired IGG vs. Nitrogen Generators

Resolution MSC.367(93) consolidated IMO requirements across three inerting technologies (merging former FSS Code Chapter 15 and Resolution A.567(14)), while MSC.457(101) refined branching, external flange connection, and recording rules effective 1 January 202427. Choice of plant depends on vessel propulsion steam availability and cargo chemical compatibility.

In a boiler uptake flue-gas system, exhaust is extracted downstream of boiler uptakes through an isolating valve fitted with open/shut indicators, soot-clearing provisions, and an interlock preventing boiler soot blowing while the IGS operates15. Raw exhaust passes into a seawater cooling and scrubbing tower required under FSS Code § 2.3.1.3 to cool the gas, strip solids and sulfur combustion products, and minimize liquid carryover via downstream filters or demisters3. Industrial and marine scrubber designs pair complementary physical mechanisms: a venturi throat accelerates gas to atomize seawater droplets and capture fine soot particulates (down to 0.2 µm in industrial venturi guides or ≥1.0 µm in GEA process data) via inertial impaction at the expense of pressure drop37, while a downstream packed-bed, tray, or spray absorption zone provides extended gas–liquid contact area to dissolve SO₂ and quench gas temperatures17. Downstream chevron or mesh demisters prevent corrosive droplets from entering the dual IG blowers15.

Diesel-propelled product, chemical/product, and shuttle tankers lacking large steam boilers rely on dedicated oil-fired IGGs featuring an integrated horizontal combustion chamber and seawater-cooled scrubber fed by dual fuel oil pumps3. Tight burner air-to-fuel control yields 1.5%–4.0% O₂ (adjustable down to 1% O₂ in vendor specifications) independent of propulsion load, alongside automatic capacity turndown and a fresh-air mode for gas-freeing5. Hybrid units (such as Maritime Protection's Flex-Inert and Flue-Gen designs) pair a venturi scrubber with main/auxiliary engine exhaust or boiler flue gas for fuel savings, automatically firing the burner for topping-up11.

Stoichiometric combustion modeling of marine diesel/MGO (approximated as 86.5% C and 13.5% H by mass) explains the resulting gas chemistry: operating at 15% excess air (λ = 1.15) yields dry flue gas containing 2.91% O₂, 13.23% CO₂, and 83.86% N₂ (with 11.0% H₂O vapor prior to scrubbing), while 25% excess air (λ = 1.25) raises dry O₂ to 4.44% (12.11% CO₂, 83.45% N₂)—near the 5% statutory limit40. In practice, manufacturer IGG datasheets report gas outlet temperatures up to 8°C above seawater temperature at ~100% humidity saturation11.

Because combustion gases carry ~12%–14% CO₂, 100% humidity, and trace sulfur species that react with or contaminate specialty chemicals, chemical tankers deploy hollow-fiber membrane nitrogen generators under FSS Code § 2.43. Air compressors deliver pressurized air through a mandatory feed-air treatment skid (coolers, water separators, and multi-stage filtration—rated by one vendor to <0.003 ppm oil carryover) to protect polymer fibers from moisture, oil fouling, and plasticization3. Inside parallel membrane modules containing millions of ~50 µm polymer hollow fibers, selective solution-diffusion permeation drives "fast gases" (O₂, H₂O vapor, and CO₂) radially through fiber walls to waste vents, concentrating "slow" N₂ inside the fiber bores at 95%–99.9% purity and ultra-low moisture (listed below −70°C dew point in a practical tanker guide)7. Purity trades inversely with throughput and compressor power, so FSS Code § 2.2.1.2 allows Administrations to accept lower-capacity chemical tanker plants if discharge rates are restricted to ≤80% of IGS capacity3. Critically, under IBC Code § 15.13.5 and IMO circulars MSC.1/Circ.1501 and MSC-MEPC.5/Circ.10, only nitrogen is permitted for cargoes containing oxygen-dependent inhibitors (such as styrene monomer inhibited with 10–15 ppm p-TBC), and inerting is prohibited before loading or during the voyage—instead occurring prior to unloading, with vapor-space O₂ carefully controlled (e.g., ≥4% O₂ per major chemical shipper instructions, or within a ~2%–8% band per IBC guidance) so the inhibitor stays active against exothermic self-polymerization24.

Engineering Parameter

Boiler Flue-Gas Scrubber System

Dedicated Oil-Fired IGG

Hollow-Fiber Membrane N₂ Generator

Primary Feedstock

Main/aux boiler exhaust + seawater + blower power3

MDO/MGO/HFO + combustion air + seawater12

Compressed air + electrical power (no gas-cooling seawater)3

Delivered Oxygen

Typically 2%–5% O₂ (load sensitive)5

1.5%–4.0% O₂ (down to 1% in vendor specs)5

0.1%–5.0% O₂ (95%–99.9% N₂)19

Gas Chemistry & Moisture

~83%–84% N₂, ~12%–14% CO₂, saturated H₂O, trace SO₂/soot15

~83%–85% N₂, ~12%–14% CO₂, ~100% saturated at ≤8°C over SW11

95%–99.9% N₂, essentially CO₂-free, ultra-dry (<−70°C dew point cited)7

Capacity Rule

≥125% max discharge rate via ≥2 blowers3

≥125% max discharge rate (1 blower allowed with full spares)3

≥125% discharge rate, or ≤80% restricted discharge on chemical tankers3

Typical Vessel Fit

Steam-propelled VLCCs and large crude tankers17

Diesel product tankers, Aframax/Suezmax tankers, FPSOs12

Chemical/parcel tankers, LNG/LPG carriers, inhibited monomers42

Main Limitation

Poor O₂ stability at low boiler load; acidic/soot corrosion5

Dedicated fuel burn; CO₂/moisture unsuitable for sensitive chemicals12

Steep compressor energy demand at >99% N₂; oil/moisture fiber fouling43

3. Non-Return Barriers: Deck Water Seal & Mechanical Non-Return Valve

Because blowers and gas generators sit inside gas-safe machinery spaces while deck piping communicates with hazardous cargo tanks, FSS Code § 2.2.3.1 mandates at least two non-return devices mounted on deck in the cargo area, engineered to prevent gas or liquid return up to cargo tank test pressure (typically 2,500 mmWG)3. The primary barrier is a Deck Water Seal (wet, semi-wet/semi-dry, or dry type) or an automated double-block-and-bleed arrangement (two shutoff valves in series with a central bleed valve programmed from flow/differential pressure to fail-safe upon power loss by closing both block valves and opening the bleed)3. Downstream (forward) of the deck seal—upstream of the first cargo tank branch—sits the second mandatory barrier: a mechanical non-return valve (check valve) with positive means of closure (or a separate positive-closing valve) plus an upstream test valve to check seat leakage3. Many installations pair this with a fail-safe (power-to-open, spring-to-close) deck isolating valve with CCR/ECR limit-switch indication and an atmospheric vent valve between the regulating valve and the non-return barrier that opens automatically upon IGS shutdown9.

Deck Water Seal Type

Hydraulic Operating Principle

Moisture Carry-Over

Blackout / Valve Dependence

Dominant Failure Modes (OCIMF Findings)

Wet Type

Gas bubbles continuously through standing water via submerged inlet pipe7

High droplet carry-over (demister required; corrosion risk)21

Passive; requires zero moving valves or power to seal7

Loss of water supply, internal corrosion perforation bypassing dip pipe, freezing3

Semi-Dry (Semi-Wet) Type

Flowing IG generates venturi/eductor suction pulling seal water into holding tank; gravity floods loop when flow stops22

Very low during normal gas flow21

Passive gravity flooding upon blower stop or total blackout22

~90% of seal-effectiveness reductions trace to scale/debris blocking venturi line or holding-tank drain loop22

Dry Type

Level sensors and automatic valves drain seal tank to drop tank during flow and refill on shutdown21

Minimal/none during normal flow21

Dependent on active automated valves, level sensors, and control power21

Valve/sensor malfunction paired with leaking mechanical NRV, lacking high-pressure shutdown21

While wet-type seals rely on simple standing water, droplet entrainment accelerates deck-main corrosion if the demister degrades21. Semi-dry seals eliminate moisture carry-over via venturi evacuation into a side holding tank, immediately flooding the seal loop by gravity whenever gas flow ceases—even during total blackout22. However, an OCIMF technical review found that approximately 90% of semi-dry seal effectiveness reductions stem from scale or debris obstructing either the venturi suction pipe (preventing pressure equalization and holding-tank drainage) or the water-return pipe into the seal loop22. Dry-type seals eliminate continuous carry-over altogether, yet OCIMF investigations following confirmed hydrocarbon backflow incidents into gas-safe spaces warn that dry seals depend on active control valves and level switches and remain vulnerable if a mechanical non-return valve leaks simultaneously and no high-pressure shutdown exists54. Under FSS Code § 2.2.3.1, any water seal must be fed by two separate pumps (each independently adequate), remain continuously watered with an always-active low-level alarm even when the IGS plant is shut down, feature freeze protection without overheating, and discharge directly overboard (never through machinery spaces) via anti-siphon water loops3. OCIMF recommends replacing float switches with ultrasonic level sensors and adding a differential-pressure shutdown if deck main pressure equals or exceeds upstream pressure22.

4. Tank Pressure Control, P/V Valves & Liquid-Filled P/V Breaker

Tanker cargo spaces are thin-walled structures typically tested to only +2,500 mmWG overpressure and −700 mmWG vacuum8, requiring a coordinated multi-tier pressure-control architecture.

Pressure Control / Protection Tier

Typical Setting (mmWG)

Equivalent (kPa / mbar)

Engineering Function

Tank Structural Vacuum Limit

−700

−6.86 kPa / −68.6 mbar

Design hull buckling/implosion threshold8

P/V Breaker (Vacuum)

−500

−4.90 kPa / −49.0 mbar

Passive atmospheric air admission if P/V valves fail or are overwhelmed8

Individual Tank P/V Valve (Vacuum)

−350

−3.43 kPa / −34.3 mbar

Primary mechanical vacuum relief per tank8

Very-Low IG Main Trip

+50

+0.49 kPa / +4.9 mbar

Operational setting for automated cargo pump trip / secondary alarm1

Low IG Main Alarm

+100

+0.98 kPa / +9.8 mbar

Mandatory FSS Code audible/visual alarm in CCR, ECR, and bridge1

Normal Operating Band

+200 to +1,200

+1.96 to +11.77 kPa / +19.6 to +117.7 mbar

Positive inert blanket maintained by regulating & recirculating/vent valves7

Individual Tank P/V Valve (Pressure)

+1,400 (Crude) / +2,000 (Chem)

+13.73 kPa (+137.3 mbar) / +19.61 kPa (+196.1 mbar)

High-velocity (≥30 m/s) primary vapor relief per tank8

P/V Breaker (Pressure)

+1,800

+17.65 kPa / +176.5 mbar

Passive liquid blowout barrier before tank test pressure or deck seal breakthrough8

Tank Test Pressure / Deck Seal Static Limit

+2,500

+24.52 kPa / +245.2 mbar

Hydrostatic tank structural limit & typical static deck-seal rating7

During cargo discharge and COW, an automatic gas pressure regulating valve at the forward bulkhead of the forwardmost gas-safe space modulates IG supply alongside an automatic recirculating or atmospheric vent valve to hold IG main pressure between roughly 200 and 1,200 mmWG3. If main pressure drops below 100 mmWG (0.98 kPa), mandatory alarms alert the CCR, machinery space, and bridge; if pressure drops further (typically 50 mmWG per industry operational guides), FSS Code § 2.2.4.5.3 mandates either an independent audible alarm or automatic shutdown of cargo pumps while leaving ballast pumps and pump-room bilge drainage pumps operational1.

Each cargo tank is fitted with a High-Velocity Pressure/Vacuum (P/V) valve (typically +1,400 / −350 mmWG on crude tankers and up to +2,000 / −350 mmWG on chemical tankers), which regulates diurnal thermal breathing and protects individual tanks whenever their lockable IG branch isolating valves are closed3. Under IMO MSC.1/Circ.677/Rev.1 and ISO 15364, resilient-seated weighted discs prevent vapour seeping until cracking pressure, then lift cleanly to eject vapor vertically at ≥30 m/s (≥2 m above deck)—exceeding hydrocarbon flame speed to block flashback8. Per a valve manufacturer advisory on ISO 15364:2021 updates referenced in MSC.1/Circ.677/Rev.1, new installations from December 2026 require FAT leakage compliance under Appendix J, flashback testing at actual set pressures, and endurance burn testing for vessels <18,000 DWT60. In freezing climates, steam or electric heat tracing is used to stop ice from locking weighted discs or flame arrestors shut7.

During loading or gas-freeing, displaced tank atmosphere vents through the deck IG main via a forward Mast Riser equipped with a manual or pressure-controlled block valve (often throttled to preserve ≥200 mmWG backpressure during purging) and a clean top flame screen7. Practical tanker standards require efflux velocities above 20 m/s at mast risers and purge stacks (maintaining ≥160 mmAq across three simultaneously purging tanks) to prevent deck-level gas pooling7.

Should mechanical P/V valves freeze or an operator pump against closed isolating or mast riser valves, the liquid-filled P/V Breaker on the un-isolated deck IG main provides a purely passive hydrostatic fail-safe8. Using a concentric inner dip pipe open to atmosphere inside an annular chamber connected to the IG main, the device blows its sealing fluid onto deck at +1,800 mmWG (+17.65 kPa) or draws fluid into the IG main to admit air at −500 mmWG (−4.90 kPa), activating safely inside tank test limits (+2,500 / −700 mmWG) and before deck-seal breakthrough (~2,500 mmWG)7. (Some older standalone designs use +2,500 / −700 mmWG settings9, though modern class guidance specifies +1,800 / −500 mmWG57).

Hydrostatic relief accuracy depends directly on fluid specific gravity (P = ρ × g × h) and zero-pressure leveling1. Breakers are charged with a 40%–60% (optimally 50%) ethylene or propylene glycol–water antifreeze per ASTM D3306 / BS 6580:1992 (or specific low-pour oil)8. Because 50 wt% ethylene glycol has a specific gravity of 1.065 (freezing point −37°C) versus 1.000 for pure water, achieving +1,800 mmWG and −500 mmWG protection requires column heights of 1,800 / 1.065 = 1,690.1 mm and 500 / 1.065 = 469.5 mm40. Topping up a 50%-glycol-calibrated breaker to the sight-glass mark with pure water lowers the blowout threshold to 1,690.1 × 1.000 ≈ 1,690 mmWG—a 6.1% premature failure40. Evaporation, seawater ingress, rolling/pitching motion, or filling while the IG main is pressurized similarly distort calibration, making periodic hydrometer checks and depressurized (0 mmWG) sight-glass verification mandatory1.

5. Lethal Asphyxiation Hazards, Corrosion & System Trips

While properly operated IGS plants dramatically suppress explosions—an inspection blog citing a 2017 DNV GL study recorded 88 tank fires and explosions (17 total losses) on oil tankers >80,000 DWT from 1980 to 2013 (nearly half during repair and tank cleaning), whereas a 2017 OCIMF 25-year chemical tanker review logged zero casualties across 35 incidents while an IGS was operating, and an earlier OCIMF study documented 20 deaths and 30 missing crew on non-inerted tankers <20,000 DWT4—inert gas creates severe asphyxiation, corrosion, and sensor hazards.

Nitrogen and flue gas are colorless, odorless, and provide no physiological warning prior to incapacitation, while combustion gas also contains 12%–14% CO₂40. Progressive oxygen depletion causes rapid collapse:

Oxygen Concentration (% vol)

Acute Physiological & Neurological Effects

20.9%–21.0%

Normal fresh air; mandatory steady concentration for tank entry69

15%–19%

Impaired coordination, reduced stamina, rising pulse/respiration; IGS space alarm triggers <19% O₂3

12%–14%

Exertion fatigue, faster breathing/pulse, impaired judgment, emotional instability, nausea68

8%–11%

Fainting within minutes without warning; 8 min at 8%–9% O₂ can be fatal (6 min ~50% fatal)68

6%–8%

Rapid unconsciousness, vomiting, lethargy; survival requires immediate resuscitation70

0%–6% (Inerted Tank / IG Supply)

Incapacitation within 1–2 breaths (~40 s coma at 4%–6%), convulsions, respiratory/cardiac arrest68

Under IMO Resolution A.1050(27), MSC.1/Circ.1401, and ISGOTT, no enclosed space may be entered without treating untested tanks as unsafe, maintaining standby rescue readiness, and verifying steady readings across all tank depths of 21% O₂, ≤1% LFL, and ≤50% Occupational Exposure Limit (OEL) for toxic components such as H₂S and benzene2. Enclosed nitrogen receiver compartments must open solely to the open deck via outward-swinging doors fitted with independent extraction ventilation, while dual O₂ sensors inside IGS machinery spaces must alarm both inside and outside below 19% O₂3.

Inside flue-gas and IGG towers, dissolved SO₂ reacts with seawater and elevated exhaust temperatures to generate low-pH sulfuric acid washwater laden with soot and chlorides, causing severe pitting and crevice attack on standard 316L stainless steel scrubbers, demisters, and overboard pipes20. Vessels combat this using Glass-Reinforced Epoxy/Plastic (GRE/GRP) towers and overboard lines (though GRE requires inspection against cracking)17, rubberized or thermoplastic internals39, 600-µm high-temperature solvent-free epoxy coatings extending across a 2-meter radius around hull overboard outlets20, super-duplex stainless steel (SDX 2507)76, or super-austenitic stainless steel UNS S31254 (254 SMO), whose ~20% Cr, 6% Mo, and 0.50%–1.00% Cu chemistry provides a PREN ≥42.5–43, a ~100°C critical pitting temperature in 3% NaCl, and dedicated sulfuric-acid resistance73.

Continuous safety relies on accurate oxygen sensing, yet analyzer technologies fail differently79. Extractive paramagnetic analyzers exploit oxygen's magnetic susceptibility (±0.01%–0.05% accuracy, <10 s response) with no consumable cell and virtual immunity to CO₂ and hydrocarbon cross-sensitivity, safely measuring flammable gas mixtures—provided sample gas coolers, filters, and condensate traps deliver clean, dry, particulate-free gas80. By contrast, heated zirconia (ZrO₂) probes (~650°C–700°C Nernst cells against ~20.9% air reference) measure oxygen partial pressure (making readings pressure-sensitive), undergo initial burn-in drift, suffer negative reading errors below ~1% O₂ when combustibles (CO, H₂, CH₄, hydrocarbons) react on the hot ceramic, and are poisoned or cracked by sulfur compounds, silicones, CFCs, pure N₂, soot, or moisture thermal shock79. Portable electrochemical cells used for tank entry rely on consumable electrolytes with 1–3 year lifespans80. Zero (pure N₂, or 0.5%–1% O₂ for zirconia) and span (20.9% clean dry air) calibrations must run at exact process temperature, flow, and pressure (≤0.5 barg) before every cargo operation1.

Finally, FSS Code Chapter 15 and IMO Unified Interpretations (MSC.1/Circ.1582) mandate automatic trips and alarms whose malfunction halts cargo operations and triggers Port State Control detention1:

Abnormal Condition / Fault

Trigger Limit

Mandatory Automated Action & Alarm (FSS Code Ch. 15 / MSC.1/Circ.1582)

High Oxygen in IG Supply

>5% O₂ by volume

Closes regulating valve and automatically vents gas to atmosphere; CCR/ECR audible & visual alarm1

Scrubber Low Cooling Water Pressure / Flow

Predetermined low limit

Shuts down IG blowers/fans and closes regulating valve (N/A to N₂); Deck Seal supply remains active1

Scrubber High Water Level

Predetermined high level

Shuts down IG blowers/fans and closes regulating valve to protect blowers (N/A to N₂)15

High-High IG Supply Temperature

>65°C blower outlet (industry setpoint)

Shuts down IG blowers/fans and closes regulating valve; audible & visual alarm1

Failure of IG Blowers / N₂ Compressors

Drive or flow loss

Automatically closes regulating valve; opens atmospheric vent / activates DB&B where fitted15

Loss of IG Supply or Power (DB&B Fitted)

Supply or power loss

Fail-safe DB&B action: block valves close automatically, bleed valve opens automatically3

Power Failure to Indicating or Control Systems

Control/instrument power loss

Audible & visual alarm in machinery space and CCR3

Low IG Main Pressure (Downstream of NRVs)

<100 mmWG (0.98 kPa)

Audible & visual alarm in CCR, machinery space, and bridge1

Very-Low IG Main Pressure

50 mmWG (industry setpoint)

Automatic shutdown of all cargo pumps (or independent audible alarm); ballast & pump-room bilge pumps stay active1

High IG Main Pressure

Typically ~90% of lowest P/V setting

Audible & visual alarm in CCR/machinery space; OCIMF recommends high-pressure shutdown on dry-type seals3

Deck Water Seal Low Water Level

Continuous monitoring

Always-active audible & visual alarm even while IGS plant is shut down (supplemented by plant-specific trips where fitted)3

N₂ Generator Specific Faults

Predetermined thresholds

Audible & visual alarms for electric heater failure, low feed-air pressure/flow, high air temp, and high separator condensate level3

IGS Machinery Space Oxygen Deficiency

<19% O₂ (dual sensors)

Audible & visual alarms inside and outside the compartment alerting responsible crew3

References

  1. Inert Gas System (IGS) & Crude Oil Washing (COW) Guide, https://seaready.net/guides/inert-gas-system-igs-and-crude-oil-washing-cow-guide
  2. INERT GAS SYSTEM (IGS) ONBOARD A VESSEL - Ships2Sail, https://ships2sail.net/blog/35
  3. resolution msc.367(93) - International Maritime Organization, https://wwwcdn.imo.org/localresources/en/KnowledgeCentre/IndexofIMOResolutions/MSCResolutions/MSC.367(93).pdf
  4. Marine Inert Gas System Maintenance & Tanker Inspection, https://marineinspection.app/blog/marine-inert-gas-system-maintenance-tanker-inspection
  5. https://cabmakassar.org/wp-content/uploads/2020/05/ISGOTT-5th-Edition.pdf
  6. Oil Tanker Cargo Handling: Systems, Pumps And Equipment, https://maritimepage.com/cargo-handling-systems-and-equipment-on-oil-tankers/
  7. IGS Main Components: A Practical Tanker Reference - Marine Public, https://www.marinepublic.com/blogs/oil-and-gas/261960-igs-main-components-a-practical-tanker-reference
  8. AMT4.5 PV Valve, PV Breaker and Tank Venting System | PDF - Scribd, https://www.scribd.com/document/997689962/AMT4-5-PV-Valve-PV-Breaker-and-tank-venting-system
  9. Inert Gas System on Oil Tankers | PDF - Scribd, https://www.scribd.com/document/719964613/1-6-Inert-Gas-System
  10. PV Breaker vs PV Valve on Ships - Pres-Vac Engineering, https://presvac.gomaritimegroup.com/pv-breaker-vs-pv-valve-on-ships/
  11. INERT GAS GENERATOR - Survitec, https://survitecgroup.com/pdf/displaypdf/s_inertgasgenerator_datasheet.pdf
  12. Maritime Protection Inert Gas Generator System - Wilhelmsen, https://www.wilhelmsen.com/globalassets/safety-systems/documents/maritime-protection-igg-brochure.pdf
  13. Inert gas generator (IGG) - Wärtsilä, https://www.wartsila.com/encyclopedia/term/inert-gas-generator-(igg)
  14. What Is a Membrane Nitrogen Generation System?, https://gasgenerationsolutions.com/what-is-a-membrane-nitrogen-generation-system/
  15. FSS Chapter 15 - Captain Damley, https://captaindamley.net/e-modules/solas-2020/solas-chapter-ii-2/fss-code/fss-chapter-15/
  16. IMSBC Code Overview and Updates | PDF | Dangerous Goods | Cargo, https://www.scribd.com/document/888644716/Anuj-f2
  17. Wärtsilä Flue gas systems (Inert Gas System - Flue type) - TES Industry, https://tesindustry.vn/en/article/new-products/wartsila-flue-gas-systems-inert-gas-system-flue-type/
  18. Annex - Unified Interpretations of Chapter 15 of the FSS Code, https://www.imorules.com/GUID-ACE1B73E-9651-4FC4-9D1E-58F236CFFAE3.html
  19. Prism Membrane Generators | PDF - Scribd, https://www.scribd.com/document/133876999/Prism-Membrane-Generators
  20. Wencon Scrubber Solutions, https://wencon.com/scrubber-solutions/
  21. Deck Water Seal - Inert Gas System on Tankers - Cult of Sea, https://www.cultofsea.com/tanker/deck-water-seal-inert-gas-system-on-tankers/
  22. Inert Gas Systems, Semi-dry Type Deck Water Seals - ocimf, https://www.ocimf.org/ru/document-libary/142-inert-gas-systems-semi-dry-type-deck-water-seals-prevention-of-inert-gas-hydrocarbon-backflow/file
  23. Voyage Data Recorder requirements - Danelec Newsroom, https://www.danelec.com/newsroom/voyage-data-recorder-regulations-and-performance-standards
  24. New statutory Tanker requirements on the installation and operation, https://maritimecyprus.com/2015/11/06/new-statutory-tanker-requirements-on-the-installation-and-operation-of-inert-gas-systems/
  25. IMO REQUIREMENTS FROM JULY 2015 TO JULY 2018 INCLUSIVE, https://maritimecyprus.com/wp-content/uploads/2015/06/statutoryupdate_no5_2015-june-1.pdf
  26. SCC 43/ Appendix 1 - Marine Department, https://www.mardep.gov.hk/filemanager/en/share/aboutus/pdf/scc/scc_m151112anx1.pdf
  27. RESOLUTION MSC.457(101) (adopted on 13 June 2019, https://wwwcdn.imo.org/localresources/en/KnowledgeCentre/IndexofIMOResolutions/MSCResolutions/MSC.457%28101%29.pdf
  28. Flammability diagram - Wikipedia, https://en.wikipedia.org/wiki/Flammability_diagram
  29. Outline - Madar, https://madar-ju.com/storage/images/files/file_17386815078IF4u.pdf
  30. Gases - Explosion and Flammability Concentration Limits, https://www.engineeringtoolbox.com/explosive-concentration-limits-d_423.html
  31. FLAMMABILITY COMPOSITION DIAGRAM - Cult of Sea, https://www.cultofsea.com/tanker/flammability-composition-diagram/
  32. Flammable Range Chart, https://ehs.msu.edu/_assets/docs/confined-space/flammable-range-chart.pdf
  33. Limiting oxygen concentration - Wikipedia, https://en.wikipedia.org/wiki/Limiting_oxygen_concentration
  34. The limiting oxygen concentration and flammability ... - CDC Stacks, https://stacks.cdc.gov/view/cdc/9780/cdc_9780_DS1.pdf
  35. TANK BARGE DANGEROUS LIQUIDS Student Manual, https://www.dcc.edu/documents/workforce-development/maritime/course-materials/studentmanualtank.pdf
  36. CCS 通 函, https://www.ccs.org.cn/ccsewwms2007/displayFileInfo.do?project=wms&file=8a8181994a95e27e014ab7ee0930001d&name=CCS537E.pdf
  37. What Are Venturi Scrubbers? How They Work | ERG APC, https://ergapc.co.uk/guides/what-are-venturi-scrubbers/
  38. 3 Key Differences Between Venturi and Packed-Bed Scrubber, https://www.cecoenviro.com/3-key-differences-between-venturi-and-packed-bed-scrubber-systems-efficiency-cost-and-application-guide/
  39. Gas Scrubbing Plants - GEA, https://www.gea.com/assets/170584/
  40. unknown_url
  41. Section 7 Inert gas systems on Tankers of 8,000 tonnes DWT and, https://www.imorules.com/LRSHIP_PT5_CH15_7.html
  42. Onboard Nitrogen Generator for Marine Vessels - Generon, https://www.generon.com/blog-marine-nitrogen-generator-onboard/
  43. LR VI.2 Nitrogen Generator Systems on Chemical ... - imorules, https://www.imorules.com/GUID-1FD52553-A165-471E-AFFA-A565064062C6.html
  44. What is Membrane Nitrogen Generation? - Minnuo, https://minnuogas.com/what-is-membrane-nitrogen-generation/
  45. Membrane Plants | A Linde Company - Linde Engineering, https://www.linde-engineering.com/products-and-services/process-plants/adsorption-and-membrane-plants/membrane-plants
  46. Nitrogen Generators Membrane Technology | PDF - Scribd, https://www.scribd.com/document/382286442/Nitrogen-Generators-Membrane-Technology
  47. Gas Safety Legislation – What you need to know! - Martek Marine, https://www.martek-marine.com/blog/gas-safety-legislation/
  48. RESOLUTION MSC.176(79) (adopted on 10 December 2004) 2004, https://wwwcdn.imo.org/localresources/en/KnowledgeCentre/IndexofIMOResolutions/MSCResolutions/MSC.176(79).pdf
  49. Cargo Handling Sheet - Styrene Monomer, https://www.shell.com/content/dam/shell/assets/en/business-functions/product/chemical/documents/v1/chs-styrene-monomer-rev-17-updated-june-23.pdf
  50. Guidelines for Carriage of Inhibited Cargoes | PDF - Scribd, https://www.scribd.com/document/976403570/17-Carriage-of-Inhibited-Cargoes
  51. Hazardous chemical cargoes - The Swedish Club, https://www.swedishclub.com/uploads/2023/12/Cargo-Advice-Hazardous-chemicals.pdf
  52. 3 Types of Inert Gas Systems You Should Know About, https://www.igiantech.com/3-types-of-inert-gas-systems-you-should-know-about/
  53. MP Flue Gas Systems - Maritime Protection - Survitec, https://survitecgroup.com/systems/mp-flue-gas-systems
  54. INERT GAS SYSTEMS DRY TYPE DECK WATER SEALS - ocimf, https://www.ocimf.org/document-libary/531-inert-gas-systems-dry-type-deck-watermarked/file
  55. What is Deck Water Seal on tanker and its types in detail?, https://marinegyaan.com/what-is-deck-water-seal-on-tanker-and-its-types-in-detail/3/
  56. What Is Deck Water Seal On Tanker and Its Types in Detail - Scribd, https://it.scribd.com/document/380633841/what-is-deck-water-seal-on-tanker-and-its-types-in-detail-docx
  57. 1.3 Typical settings of pressure/vacuum relief devices, https://imorules.com/GUID-F2210755-6A1D-419D-8E65-C2508E541498.html
  58. High Velocity PV Valve - Factory from China - CCS/EC/ABS Certificate, https://www.rightmarine.com/product/high-velocity-pv-valve/
  59. MSC.1-Circ.677-Rev.1 - Register-iri, https://www.register-iri.com/wp-content/uploads/MSC.1-Circ.677-Rev.1.pdf
  60. P-06 HIGH-VELOCITY VENT VALVE, https://www.ccs.org.cn/ccswzen/file/download?fileid=202603110971089152
  61. Scanvent High Velocity P/V Valves - Tank Cleaning Technologies, https://tankcleantech.com/high-velocity-pv-valves/
  62. Newly released revision of the IMO/677 concerning high velocity, https://presvac.gomaritimegroup.com/newly-released-revision-of-the-imo-677-concerning-high-velocity-pressure-vacuum-valve/
  63. High Velocity Valve Specifications for Tankers | PDF - Scribd, https://www.scribd.com/document/975425065/O15-A-HIGH-VELOCITY-PRESSURE-VACUUM-VALVES-TYP-FINAL-DRAWING
  64. High Velocity P/V Relief Valve - TANKTECH - Catalogs Nauticexpo, https://pdf.nauticexpo.com/pdf/tanktech/high-velocity-p-v-relief-valve/31694-75939.html
  65. Cargo and Ballast Operations Manual | PDF | Oil Tanker - Scribd, https://www.scribd.com/document/843143023/Ch-7-5-Cargo-Ballast-Operations
  66. PV Breaker Inspection and Maintenance Guide | PDF | Density - Scribd, https://www.scribd.com/document/792250099/PV-Breaker-inspection-maintenance-check-density-of-liquid-antifreezev
  67. Inert gas systems - ocimf, https://www.ocimf.org/document-libary/96-inert-gas-systems-the-use-of-inert-gas-for-the-carriage-of-flammable-oil-cargoes/file
  68. IGG Manual | PDF | Combustion | Valve - Scribd, https://www.scribd.com/document/686682984/IGG-manual
  69. MSC.1/Circ.1401 9 June 2011 GUIDELINES ON TANK ENTRY FOR, https://www.register-iri.com/wp-content/uploads/MSC.1-Circ.1401.pdf
  70. HAZARDS OF INERT GASES AND OXYGEN DEPLETION, https://asiaiga.org/uploaded_docs/AIGA%20008_11_Hazards%20of%20inert%20gases%20and%20oxygen%20depletion.pdf
  71. Oxygen Deficient Atmosphere Hazards - CO2 Meter, https://www.co2meter.com/blogs/news/oxygen-deficient-atmosphere-hazards
  72. BTOCT Basic Training Course Overview | PDF | Oil Tanker - Scribd, https://www.scribd.com/document/459082864/MC-1-01-BTOCT-2014-pdf
  73. UNS S31254 Chemical Composition: A Complete Guide to 254, https://www.shalco.com/blog/uns-s31254-chemical-composition-comprehensive-guide-to-254-smo
  74. 254 SMO Super Stainless Steel (S31254) - KAYSUNS, https://www.kaysuns.com/blog/254-smo-super-stainless-steel-s31254/
  75. GRP Vessels & Scrubbers | Air Pollution Control, https://unionfbr.com/products/grp-vessels-scrubbers.php
  76. Marine scrubbers sail ahead with specialist stainless steels, https://www.manifoldtimes.com/news/outokumpu-marine-scrubbers-sail-ahead-with-specialist-stainless-steels/
  77. Alleima® 254 SMO Tube and pipe, seamless, https://www.alleima.com/en/technical-center/material-datasheets/tube-and-pipe-seamless/alleima-254-smo/
  78. Sandvik 254 SMO - Applied Alloys International, https://www.appliedalloys.com.au/wp-content/uploads/2018/06/254SMO.pdf
  79. Oxygen Analyser Calibration for Inert Gas Systems - Alrightes, https://alrightes.com/oxygen-analyser-calibration-for-inert-gas-systems/
  80. Oxygen Analyzers | Zirconia, Paramagnetic & TDLAS | GESHINE, https://geshine.com/gas-analyzers/oxygen-analyzers/
  81. Paramagnetic Oxygen Analyzer: Principles & Uses | Tomarok, https://tomarok.com/paramagnetic-oxygen-analyzer/
  82. Oxygen Analyzer for Inerting | Fresenius Instruments, https://freseniusinstruments.com/solutions/inerting/?lang=en
  83. Off-Gas Analyzer Selection, Calibration & Troubleshooting, https://bioprocesstools.com/blog/off-gas-analyzer-selection/
  84. Oxygen analysis - How to choose an oxygen analyzer? - ASaP, https://www.asap.nl/oxygen-analysis-how-to-choose-an-oxygen-analyzer/
  85. 9 Step Zirconia Oxygen Analyzer Calibration Procedure, https://automationforum.co/9-step-zirconia-oxygen-analyzer-calibration-procedure/
  86. Zirconium Dioxide (ZrO2) Oxygen Sensor Installation, Operation and, https://sstsensing.com/wp-content/uploads/2025/06/AN-0050_Zirconia-Sensor-Operation-and-Compatibility-Guide.pdf
  87. XPM601 Paramagnetic Oxygen Analyzer User Manual, https://www.processsensing.com/docs/manual/XPM601-97632-Manual.pdf
  88. 10 Step Oxygen Analyzer Calibration Procedure: Paramagnetic Type, https://automationforum.co/10-step-oxygen-analyzer-calibration-procedure-paramagnetic-type/
  89. C C S Technical Information, https://www.ccs.org.cn/ccsewwms2007/displayFileInfo.do?project=wms&file=000000006247e50d016270521683003e&name=/wms/Technical+Notice+on+%E2%80%9CUNIFIED+INTERPRETATIONS+OF+CHAPTER+15+OF+THE+FSS+CODE%E2%80%9D+(MSC.1-Circ.1582)1522302850689.pdf