Ship Subsystems & EngineeringSkipssystemer og maskinteknikk · Engineering system cardTeknisk systemkort

Heavy-Duty Stern Rollers on Anchor Handling Tug Supply Vessels

Installed across the transom stern of an Anchor Handling Tug Supply (AHTS) vessel, the stern roller provides a low-friction, high-load cylindrical rolling surface bridging the working deck and sea.

min readmin lesing
22
wordsord
4,636

#AHTS#Stern Roller#Offshore#Towing

Part 1: System cardDel 1: Systemkort

1. Core Function

Installed across the transom stern of an Anchor Handling Tug Supply (AHTS) vessel, the stern roller provides a low-friction, high-load cylindrical rolling surface bridging the working deck and sea1. It smoothly guides heavy rig anchors, mooring chains, steel work wires, and subsea mooring lines during deployment, tensioning, and recovery1. Rotating under severe downward and oblique line loads, the assembly lowers line bending stress, prevents deck-edge wire chafing, and transmits operational forces into the transom framing4.

2. Primary Operational Tasks

  • Low-Friction Wire, Chain, and Rope Guidance: Rotates under tension to minimize sliding friction and bending fatigue across specified curvature ratios during towing, anchor handling, and deep-water mooring recovery2.
  • Absorbing Extreme Vertical Anchor Breakout Forces: Sustains high resultant bearing reactions generated by winch line pull, near-vertical seabed extraction angles, and swell-induced stern heave and pitch accelerations11.
  • Protecting Transom Plating from Abrasion: Shields aft hull plating and stern structure—working alongside sloped aft bulwark transitions and thick deck drag plates—against severe steel wire, chain, and anchor scoring3.
  • Guiding Large Anchor Flukes Smoothly onto Deck: Provides adequate width and landing geometry so wide high-holding-power anchor flukes board cleanly onto the stern bolster without snagging or damaging anchor shanks4.
  • Supporting Multi-Line and Off-Centerline Operations: Interfaces with retractable towing pins and shark jaws to constrain dual-line paths while managing off-centerline lateral and heeling moments17.

3. System Interconnections

  • Inputs: Mechanical line loads (vertical downward, longitudinal, and oblique tensions from anchor-handling/towing winches and outboard mooring tackle) transmitted into reinforced transom hull framing, mounting blocks, intercostal stiffeners, and aft deck drag plates (e.g., 25 mm thick in a 75 m AHSV specification)3. Service feeds include centralized automatic grease lines (e.g., SKF KFG auto-lube pumps supplying mineral or biodegradable grease)3, enclosed oil lubrication arrangements7, or open seawater lubrication/flushing grooves on polymer bearings25, plus deck water spray for cooling synthetic ropes during deep-water payout5.
  • Outputs: Reduced line friction and wire/rope bending stress4, combined with distributed radial and axial thrust reactions routed through end bearings and cones into transom foundations and intercostal hull stiffeners4. Diagnostic instrumentation is optional rather than universal: enclosed oil-lubricated designs specify oil-level or flow control7, polymer bearing manuals address water-flow and temperature monitoring26, and integrated bridge systems log line tension29; however, public vessel specifications do not document standard onboard bearing-temperature or grease-flow telemetry sensors on conventional greased stern rollers.

4. Redundancy & Criticality

Classification Societies treat the stern roller as critical associated anchor-handling equipment whose failure threatens line integrity, deck safety, and vessel stability1. Vessel specifications show 150–350 t Safe Working Load (SWL) ratings on smaller and mid-size AHTS vessels3, 450–550 t SWL on single-drum heavy units34, and up to 750 t Maximum Working Load (MWL) or 800 t SWL per side (including 2 × 800 t SWL twin assemblies) on large deep-water vessels20. Under 2026 Korean Register (KR) rules, supporting foundations and mounts must be dimensioned for 2× SWL or 2× maximum winch line pull (whichever is greater), while the roller itself must exceed 2.5× SWL4. ABS rules require design loads to incorporate maximum hoisting, rendering, and braking forces including dynamic effects13, Bureau Veritas (BV) frameworks apply Dynamic Amplification Factors (DL = DAF × T) alongside winch brake holding loads41, and engineering verification uses project-specific Finite Element Analysis (FEA)7. Enclosed bearing housings rely on multi-lip or labyrinth waterproof seals and tightness testing to prevent seawater ingress7; however, dedicated anchor-handling rules such as KR 2026 leave specific bearing-seal designs and watertight boundary rules to general steel-ship structural rules4. Under KR 2026 rules and industry compliance guidance referencing IMO MSC.1/Circ.1663, current load-holding certificates, visible SWL markings, annual thorough examinations, groove-wear surveys, and five-yearly Special Survey re-tests (with Non-Destructive Testing on hull welds where required) are mandatory and Port State Control detainable1.

Part 2: Technical deep diveDel 2: Teknisk dybdeanalyse

1. Stern Roller Geometry & Single vs. Split Designs

Heavy-duty AHTS stern rollers span a wide dimensional envelope governed by bollard pull, winch pull, rig anchor width, and transom notch geometry. Coastal and mid-size AHTS vessels (roughly 40–86 t bollard pull) commonly fit single cylindrical rollers measuring 1.4–1.8 m in diameter by 3.5–5.0 m in length, rated for 150–300 t SWL3. On large deep-water AHTS vessels, documented roller dimensions span 2.0–4.0 m (and up to 4.5 m listed on Pacific Discovery) in diameter and 4.0–8.0 m in total width, with capacities of 350–550 t SWL in single-drum configurations and 750 t MWL to 800 t SWL per drum in twin or split configurations20.

Vessel / Specification

Architecture

Roller Dimensions (Width × Dia)

Rated Capacity (SWL / MWL)

Operational Context

VOS Challenge

Single roller

5.0 m × 1.6 m

300 t

Mid-size DP2 AHTS30

Britoil Dynamic

Single roller

5.0 m × 2.2 m

350 t SWL

Mid-size AHTS32

HF Offshore / 125-Ton AHTSSV

Single roller

5.0–6.0 m × 2.5 m

450 t SWL

Heavy AHTS34

Boskalis Bear

Single roller

6.0 m × 3.0 m

500 t SWL

Large deep-water AHTS35

BB Octopus

Single roller

6.0 m × 3.5 m

550 t SWL

Large North Sea AHTS36

Ulstein Far Santana (YNO 249)

Double roller

6.0 m × 4.0 m

500 t SWL

High-power AHTS48

Njord Viking

Split roller

6.0 m total × 4.0 m

750 t MWL each

Heavy anchor handling37

Siem Opal

Double roller

2 × 4,000 mm (8.0 m total; dia unstated)

800 t SWL

Waterfall winch AHTS20

Pacific Discovery

Double (RRM)

2 × (3.0 × 4.5 m) (dia/width order unstated)

750 t MWL @ 90°

Deep-water AHTS38

Maersk Topper

Twin / Double

Not stated in spec

2 × 800 t SWL

Ultra-heavy DP2 AHTS39

Selecting between a single full-width roller and a twin or split assembly trades geometric simplicity against multi-line kinematics and shaft stiffness. A single full-width drum offers an uninterrupted cylindrical track across the transom, simplifying wide-fluke anchor boarding without central structural obstructions4. However, deep-water AHTS vessels routinely operate twin-drum or waterfall winches managing two lines simultaneously (such as running a chaser pennant while holding a mooring wire)20. Because a one-piece barrel can rotate at only one angular velocity, differential line speeds or opposing pay-in/pay-out directions force at least one wire to skid across the steel surface, accelerating chafe and frictional heat. Twin or split designs divide the span into two coaxial drums supported by a central bearing pedestal, allowing each half to rotate independently with its respective line20. Splitting a 6.0–8.0 m span also halves the unsupported bending length of the shaft, curbing central deflection and bearing edge-loading under 750–800 t loads per side20. The operational penalty is an additional central pedestal gap that demands careful towing-pin alignment to avoid pinching lines, plus doubled bearing and seal inspection points.

Structurally, the cylindrical barrel is fabricated from thick-walled high-tensile strength steel2 flanked by tapered end cones that prevent lines from dropping into end-housing gaps7. Inside the shell, radial internal stiffeners (diaphragm/ring webs) resist shell ovalization under concentrated contact loads and transfer forces into the central forged steel shaft and end mounting blocks7. Classification approval relies on project-specific FEA verifying the shell, cones, internal stiffeners, shaft, bearing reactions, mounting blocks, and vessel hull interface against extreme load cases7. Exact shell plate thicknesses (in mm) and radial web spacings are proprietary yard and OEM details not published in open specifications, though adjacent aft hull drag plates are specified around 25 mm thick and backed by intercostal transom stiffeners3.

Geometrically, KR 2026 anchor-handling guidance specifies keeping roller length as short as practicable while accommodating the widest anticipated anchor4, and enforces a minimum outer diameter relative to the anchor-handling wire rope diameter:

Equation

For an 83 mm steel work wire50, this criterion sets a 1.41 m minimum roller diameter; large 3.0–4.0 m rollers yield Equation ratios of roughly 36–48, well above the Equation fairlead example in the 2022 API RP 2SK draft51 and the Equation minimum low-tension bend threshold cited in anchor-handling manuals16. Equipment integration guidance from SHM Solutions recommends a 45° alignment toward the working deck2, paired with aft bulwark tops contoured to slope smoothly down onto the roller so tow wires never catch on sharp deck edges3.

2. Bearing Systems & Sealing Architecture

Stern roller bearings operate in an extreme tribological regime combining near-static breakaway, slow reversing rotation, intense shock loads, continuous salt spray, intermittent immersion, and abrasive seabed mud brought aboard on chains and anchors11. Three main bearing architectures compete in service: heavy-duty spherical roller bearings (SRBs), traditional greased bronze bushings, and self-lubricating polymer or composite journal bearings2.

Feature

Spherical Roller Bearings (Grease/Oil)

Bronze Sleeve Bearings (Greased)

Polymer / Composite Journal Bearings (Thordon, Orkot)

Contact & Deflection

Rolling line/point contact; spherical raceways tolerate modest shaft bow2

Rigid metallic sliding contact; prone to edge loading under shaft bend3

Compliant sliding surface; deflects slightly under misalignment to widen load zone26

Dynamic Pressure Limits

High rolling capacity; dependent on intact lubricant film and clean raceways26

Moderate capacity; vulnerable to galling/seizure if grease starves26

Thordon XL: 5.5 MPa; SXL: 10–12 MPa; ThorPlas: 31–45 MPa; HPSXL TRAXL spherical: 27.5–55.0 MPa (70 MPa peak static)25

Lubrication Supply

Centralized SKF KFG auto-lube grease pump (mineral or EAL) or enclosed oil bath7

Continuous manual or automated high-pressure grease injection3

Grease-free seawater flushing via axial grooves, or dry-running grades (Orkot TXMM)26

Sealing Architecture

Enclosed end caps with labyrinth waterproof seals (e.g., GMN) or lip/mechanical seals; tightness tested7

Lip/labyrinth seals required to retain grease and block seabed grit26

Open seawater flushing without oil seals, or split Thorseal wiper seals (0–100 MPa) to exclude grit28

Failure Mode & Constraints

Seal breach admits seawater causing internal corrosion and grease/oil discharge26

Rapid wear and seizure upon grease starvation (ES Kestrel case)53

Zero oil pollution risk; requires corrosion-resistant mating liners (316/Duplex SS, NiCrB) at Ra 0.4–0.8 µm26

Note: Trelleborg/Ship-Technology literature also notes approvals up to 35 N/mm² (35 MPa) mean for Orkot composite pads in hatch-cover applications, alongside Orkot TLMM/TXMM deployments in stern roller bearings56.

Spherical roller bearings (SRBs)—such as SKF units mounted on forged steel shafts2—provide low breakaway torque under massive radial loads and accommodate minor elastic shaft deflection through spherical outer raceways. Because rolling steel elements rapidly corrode and seize if exposed to seawater26, SRBs rely entirely on positive sealing and continuous lubrication. Common arrangements use centralized automatic grease pumps (e.g., SKF KFG units23) dispensing mineral or biodegradable Environmentally Acceptable Lubricant (EAL) greases24, or enclosed oil-lubricated housings fitted with oil-level/flow control and leak-prevention assemblies7. End-cap protection employs bolted housing covers with multi-lip elastomer seals and non-contact labyrinth waterproof seals (e.g., GMN labyrinth arrangements27) maintained under slight positive internal grease purge. Detailed seal-stack drawings for proprietary SRB rollers are OEM-specific and not standardized in public rules; as noted in KR 2026 guidance, explicit bearing and sealing specifications are left to general steel-ship classification rules4.

To eliminate grease consumption, overboard lubricant leakage, and seal-induced seizures, Thordon Bearings reports that more than 80 AHTS vessels worldwide now run self-lubricating elastomeric and composite journal bearings in stern rollers28. Unlike rigid bronze sleeves, elastomeric grades (such as Thordon SXL) deflect slightly under shaft bending to distribute edge pressures over a broader contact zone and damp impact shocks26. Standard water-lubricated sleeves incorporate longitudinal water grooves—typically 7 mm deep and 7 mm wide on shafts ≥400 mm—to circulate seawater cooling and flush seabed grit26. Where heavy coastal silt threatens bore wear, split cut- and tear-resistant Thorseal elastomer wiper seals (rated for 0–100 MPa) exclude particulates while maintaining a grease-free assembly28. Pressure capability scales steeply by polymer grade per manufacturer manuals: Thordon SXL handles 10 MPa dynamic in limited motion (and up to 12 MPa in the ES Kestrel split-housing retrofit)28, thermoplastic ThorPlas reaches 31 MPa in full tubular sleeves28 and up to 45 MPa in marine installations25, and metal-backed HPSXL TRAXL spherical bearings cover 27.5–55.0 MPa normal operation (70.0 MPa peak static)26. Fabric-reinforced thermoset Orkot composites similarly offer minimal water swell, roughly one-sixth the mass of steel, galvanic immunity, and suppressed dry stick-slip in TXMM grades55. Because polymer bearings depend on shaft smoothness rather than thick hydrodynamic oil films, journals require corrosion-resistant liners—such as annealed 316 stainless steel (205 HB), Duplex 2205 (290 HB / 30.5 HRC), S17400 (33–44 HRC), or nickel-chrome-boron (NiCrB) hard-coated sleeves—finished to Ra 0.4–0.8 µm (with up to 1.6 µm acceptable in Thordon manuals and 0.7 µm / 32 RMS recommended in CIP Composites guidance)26.

3. Anchor Breakout Physics & Dynamic Shock Loads

During anchor recovery, the stern roller acts as a structural pivot turning nearly horizontal deck winch pull into a steep downward seabed extraction vector17. From free-body statics, the resultant load vector R carried by the roller shell and bearings is the vector sum of the inboard winch tension T_winch and the outboard sea-side tension T_out:

Equation

Assuming a freely turning, low-friction drum (Equation), a horizontal deck lead, and an outboard wire departing at angle Equation below horizontal (giving total wrap/deflection angle Equation), the forward horizontal resultant Equation, downward vertical force Equation, and total bearing resultant magnitude Equation are:

Equation

When the AHTS stations directly above the anchor for breakout, the wire approaches vertical (Equation—the design condition cited for Pacific Discovery's 750 t MWL @ 90° rating38 and the Norwegian Maritime Directorate's stability check at the upper edge of the stern roller62). At Equation, the vertical transom force peaks at Equation while the total resultant load on the drum reaches Equation, acting 45° forward and downward. If astern drift or surge pulls the wire underneath the stern counter (Equation), Equation decreases slightly while the total resultant Equation continues climbing toward Equation. Simultaneously, trapping the line through outer towing pins offsets this multi-hundred-tonne downward load laterally from the centerline, imposing severe rolling and heeling moments on the vessel17.

Breaking out deeply buried High-Holding-Power (HHP) fluke anchors (such as Stevpris Mk7 or Bruce designs) compounds these static vectors with nonlinear soil mechanics12. Field recovery trials reported on Stevpris Mk7 anchors (May 2023) highlight stark differences in breakout direction14. Pulling forwards (toward well center) along the anchor's strongest axis works for shallow sand settings at 1.5–2× water-depth scope, yet peak retrieval tensions reach 100–110% of original installation load and persist longer than chain breakout; for middle or mud fluke angles, forward pulling either buries the anchor deeper or requires shortening scope so aggressively that the system becomes dangerously stiff14. Pulling backwards with a chaser or pennant wire rotates the flukes upward out of the mud at lower loads (e.g., stepping up from 150 t at 1.4×–3× water depth in 50 t increments), though it risks inward buckling at the shank connection14. Once seabed suction and soil shear collapse suddenly—or if an AHTS turns 180° and accelerates against a braked winch—stored elastic strain releases violently11. Vendor deck-machinery engineering guidance notes that anchor breakout shocks can reach 2–3× static chain tension11.

Wave-induced vessel dynamics sharply amplify these transients. Because the stern roller sits at the vessel's aft extremity, pitch and heave combine to maximize vertical stern velocity14. When long mooring scope leaves grounded chain or wire catenary on the seabed, geometric sag absorbs vessel heave cycles14. When pulling nearly up-and-down during final breakout with zero grounded scope, catenary compliance vanishes; every upward heave/pitch excursion of the stern roller must be absorbed purely by axial elastic stretch across a short suspended wire of stiffness Equation14. Because steel work wire combines high axial rigidity (Equation) with short suspended length (Equation) near lift-off, even moderate swell produces severe dynamic tension spikes across the roller14. Classification rules reflect these amplified transients through service-based Dynamic Amplification Factors (DL = DAF × T in BV rules)41, hoisting/rendering/braking dynamic envelopes (ABS rules)13, and KR 2026's 2× foundation and 2.5× roller SWL factors4.

Post-incident investigations by Havtil (2022, prepared by DNV) and operator requirements (e.g., Equinor, Delmar, and DNV-RU-OU-0300) establish a critical operational boundary: mooring chain must not be placed over the stern roller during anchor breakout except under very low tension; instead, a steel work wire or sacrificial chain must take high breakout loads14. High-strength R4 and R5 mooring links bent over a curved roller experience combined tension, in-plane bending (IPB), out-of-plane bending (OPB), and torsion that curtail fatigue life and foster Hydrogen Induced Stress Cracking (HISC)—requiring the vessel's Impressed Current Cathodic Protection (ICCP) system to be switched off 6 hours prior to and during chain immersion over the roller, or electrically isolated using a fiber rope insert29.

4. Surface Metallurgy & Synthetic Fiber (HMPE) Compatibility

Stern roller shell metallurgy faces competing requirements: the barrel must endure severe point-contact stresses and sliding from 70–166 mm high-strength steel rig chains40 and armored work wires without grooving, while staying smooth and burr-free enough to deploy deep-water polyester and High-Modulus Polyethylene (HMPE, such as Dyneema or Spectra) mooring lines without thermal or abrasive damage5.

On AHTS stern decks, severe wear zones and stopper forks commonly specify quenched-and-tempered abrasion-resistant steel such as Hardox 450 or hard-facing68, whereas stern roller barrels are built from high-tensile steel2; exact Brinell/Rockwell surface-hardness targets for roller shells are proprietary to OEMs and are not stated in public specifications or classification rules. Preventing grooving is essential for chain integrity as well as synthetic ropes. Fracture-mechanics work cited in Havtil's 2022 chain study (Xue et al., 2021) demonstrated that tensioning mooring chain over curved surfaces cuts fatigue life sharply relative to straight tension—shallow grooves induce extra in-plane bending (IPB), while deep grooves force links into out-of-plane bending (OPB)29. Moreover, high contact pressures and friction against hard steel induce plastic surface deformation and untempered martensite layers on R4/R5 links where surface cracks initiate and grow rapidly under seawater HISC29. Consequently, OCIMF OVIQ4 inspections and 2026 lifting-gear guidance mandate routine wire-groove wear surveys across stern rollers1.

Line Material

Thermal Melt Limit

Recommended Roller Surface Roughness

Minimum Bend Ratio (D/d)

Required Operational Controls over Stern Roller

Steel Work Wire / R4–R5 Chain

High thermal tolerance; contact friction can form untempered martensite on chain29

Standard machined steel finish (e.g., Ra ≤ 3.2 µm tolerated by wire)8

KR 2026: ≥17× wire dia4; API RP 2SK draft: ~16× fairlead51; >6 at low tension16

Break out anchors on work wire, not mooring chain; shut off ICCP 6 h prior to chain immersion14

Polyester Deep-Water Rope

Melts around 260°C; thermally insulating but jacket abrades on rough steel66

Smooth, burr-free non-corroding finish; wear scales linearly with Ra8

≥8–10× rope dia (synthetic fairlead guidance; exceeded by 2–4.5 m drums)8

Keep straight lead (<1.5–2° fleet angle); remove weld spatter/burrs; spray cooling water in deep payout5

HMPE (Dyneema / Spectra) Rope

Melts around 140–150°C; prone to cold flow/creep8

Mirror finish: Ra ≤ 0.8 µm recommended by fairlead vendor guidance (vs. Ra 3.2 µm wire baseline)8

≥8–10× rope dia (synthetic fairlead minimum)8; >6 at low tension16

Confirm free rotation; dress rust/grooves; eliminate side-plate gaps (nipping); continuous water cooling; limit oil/grease contact5

For deep-water synthetic mooring lines, surface finish and heat dissipation dictate survival. Although HMPE offers exceptional strength-to-weight efficiency (0.97 specific gravity) and cyclic bending life, its melting point is only 140–150°C (compared with ~260°C for polyester, which is often braided as an outer protective jacket with sand-filter barriers around parallel HMPE sub-cores)5. Any frictional work dissipated at the roller surface (Equation) converts directly into local heat72. While conventional steel-wire rollers commonly operate near Ra 3.2 µm (the US Navy fairlead baseline) or rougher8, fairlead vendor engineering guidance specifies a mirror-smooth Ra ≤ 0.8 µm finish for HMPE because microscopic steel burrs and weld spots act like blades against fine polymer filaments5. Laboratory cyclic-abrasion testing across roughness values from 7.6 to 254.3 µm Ra confirmed a linear relationship between roughness and early-stage strength loss, demonstrating that corroded steel rollers at Ra 128.5–254.3 µm reduced tested synthetic mooring rope residual strength to 14% MBL before rupture67.

Maintaining a mirror Ra ≤ 0.8 µm finish on a carbon-steel AHTS stern roller that alternates between steel rig chain and synthetic rope is rarely practical67. Deep-rope manuals and API RP 2SM guidelines therefore pair surface dressing with operational controls: grinding away rust blooms, grooving, and welding spots prior to mobilizing fiber lines; keeping the line straight over a freely spinning drum (fleet angles below 1.5° on grooved winch drums or 2° on smooth drums); minimizing clearances between the drum and side plates so flattened, tensioned HMPE cannot wedge and slice ("nipping"); spraying fresh or seawater continuously across the rope at the stern roller during deep-water payout to prevent overheating; and minimizing oil or grease exposure (a distinct operational advantage of water-lubricated bearings)5.

5. Failure Modes, Seized Rollers & Dry-Dock Overhaul

Because the stern roller acts as a single-point load transfer interface across the transom, mechanical or tribological degradation quickly escalates into wire, anchor, or bearing failure8.

Seized Rollers & Catastrophic Chafing: Roller seizure commonly stems from centralized or manual grease-system failure, seawater ingress through damaged end seals, corrosion during layups, or shock damage26. Once the drum locks stationary, rolling contact becomes dry sliding friction8. Steel work wires sliding across a jammed barrel carve deep preferential grooves into the shell while rapidly abrading outer wire strands toward discard limits (such as KR 2026's thresholds of ≥5% broken wires in 10× rope diameter or ≥7% diameter loss) and risking catastrophic parting under swell surges4. When polyester or HMPE ropes drag over a seized steel roller, dry sliding friction heats the outer filaments past HMPE's 140–150°C melting point, causing severe jacket fuzzing (a 25% abrasion wear threshold is cited in braided-rope vendor guidance as the retirement limit77) and thermal melt failure within seconds5.

Shell Denting, Fluke Impacts & End-Bearing Seal Failure: Boarding massive drag-embedment anchors exposes the drum, end cones, and aft drag plates to heavy impact loading from sharp anchor flukes and shanks15. Local shell denting, flat spots, and chain scoring degrade drum concentricity and create stress concentrators at internal stiffening web welds, while misangled recovery can simultaneously damage anchor shanks or flukes7. At the transom ends, seals operate amidst wave slam, stern immersion, and abrasive mud; once an elastomer lip or labyrinth seal fails, seawater flushes out lubricant, pits bearing raceways and shaft journals, and discharges grease or oil overboard11.

Inspection, Dry-Dock Overhaul & Afloat Bearing Replacement: Classification and industry regimes combine monthly/annual fairlead and groove-wear surveys with five-yearly Special Surveys and twice-in-five-years docking surveys1. Condition monitoring uses Ultrasonic Thickness Measurement (UTM) gauging of deck drag plates and roller shells alongside Magnetic Particle (MT), Ultrasonic (UT), or Penetrant Testing (PT) of cone, internal-stiffener, and hull-foundation welds4. During a full dry-dock overhaul, crews typically execute a structured mechanical teardown:

  1. Unbolting the split bearing housings and mounting blocks while supporting the drum via dockyard cranes rigged to a certified spreader beam (provided by OEMs such as SHM Solutions)2.
  2. Lifting the roller assembly clear of the transom notch for workshop shaft extraction, journal refurbishment or hard-coated NiCrB sleeve replacement, and shell weld repair/re-machining2.
  3. Installing replacement SRBs or polymer bushings—where elastomeric sleeves are interference-fitted by freeze shrinking with dry ice (-78°C) or liquid nitrogen (-196°C) and retained axially by bolted keeper rings (set-screws, flanges, and nearby welding are prohibited on polymer bearings), with water-flushing grooves machined prior to housing fit26.
  4. Completing shaft alignment verification, lubrication-system flow testing, and housing tightness checks upon reinstallation7. Specific hydraulic jacking tonnages and press clearances for pulling seized full-length forged shafts from enclosed roller bores are proprietary to yards and OEMs and are not published in open technical manuals.

Where split housings and split bearings are fitted, repairs no longer invariably require dry-docking. In May 2024, vendor technical reports document that Ocean Power International (OPI) replaced the seized, grease-starved bronze stern-roller bearings on the 2011-built AHTS ES Kestrel while the vessel remained afloat and operational53. Because the transom structure prevented axial shaft withdrawal, technicians unbolted and lifted the upper split-housing caps, removed the worn bronze bushings, slipped custom-machined 360 mm-long grease-free Thordon SXL bearings directly over the stationary pin prior to re-seating the roller, and interference-fitted them into the split housings without replacing the shaft53. Paired with hydraulically extracted tapered keyset carriers and split Thorseal lip seals, modern split-bearing architectures allow operators to restore free roller rotation and seal protection pierside without full axial shaft extraction25.

References

  1. Offshore Vessel Inspection: MODU, AHTS and PSV Compliance, https://marineinspection.app/article/offshore-vessel-inspection-modu-ahts-psv-2026-compliance
  2. Stern Roller - SHM Solutions, https://www.shmsolutions.no/en/deck-equipment/stern-roller
  3. SPECIFICATION FOR 75 METRE ANCHOR HANDLING SUPPLY, https://maritimeexpert.wordpress.com/wp-content/uploads/2016/12/75m_supply-vessel-full-specification_ahsv.pdf
  4. Guidance for Anchor Handling Appliance, https://www.krs.co.kr/KRRules/KRRules2026/data/DATA_OTHER/ENGLISH/Guidance%20for%20Anchor%20Handling%20Appliance_2026.pdf
  5. Pennant Buoy and Mooring Systems Guide | PDF | Anchor | Rope, https://www.scribd.com/document/658646825/Appendix-11-B-rev-Anchor-handling
  6. Anchor Handling and Towing Guidelines | PDF - Scribd, https://www.scribd.com/document/381691877/Anchor-Handling-Guide
  7. AHTS Stern Roller for Anchor Handling Vessels | Fixed or Rotating, https://m.shipdeckequipment.com/sale-44700568-ahts-stern-roller-for-anchor-handling-vessels-fixed-or-rotating-shaft.html
  8. Marine Roller Fairlead: How to Choose, Position, and Maintain the, https://www.boomarine.com/marine-roller-fairlead-how-to-choose-position-and-maintain-the-right-one
  9. Damage caused by the wire rubbing the stern roller, crash ... - Gauth, https://www.gauthmath.com/ph/solution/1987900140259460/Damage-caused-by-the-wire-rubbing-the-stern-roller-crash-rails-stern-gate-or-tow
  10. Zhongyuan Ship Machinery Manufacture (Group) Co., Ship stern roller, https://www.nauticexpo.com/prod/zhongyuan-ship-machinery-manufacture-group-co/product-200337-584755.html
  11. Shark Jaw & Towing Pin Systems for AHTS Vessels | SharkJaw, https://sharkjaw.net/applications/ahts-vessel/
  12. H) Analysis of Structural Strength at the Stern with the Addition of, https://www.researchgate.net/publication/415565985_H_Analysis_of_Structural_Strength_at_the_Stern_with_the_Addition_of_Stern_Roller_on_TB_ASL_Prosper_VI_Ship_Check_for_updates
  13. Rules for Building and Classing Marine Vessels 2021 - Part 5D, https://ww2.eagle.org/content/dam/eagle/rules-and-guides/archives/other/1_marinevesselrules_20211/mvr-part-5d-july21.pdf
  14. Delmar Systems, https://riggflytt.com/wp-content/uploads/2024/05/20-Praktisk-gjennomgang-%E2%80%93-Recovery-av-anker.pdf
  15. Stavanger UTM: Thickness Measurement for Offshore Vessels, https://atlantisndt.com/maritime/stavanger
  16. vryhof - anchor manual 2005 - TU Delft OpenCourseWare, https://ocw.tudelft.nl/wp-content/uploads/AM2000.pdf
  17. VESSEL ANCHOR HANDLING MANUAL TEMPLATE MSF Rev01a, https://www.studocu.vn/vn/document/truong-dai-hoc-fpt/thuc-hanh-quan-ly/vessel-anchor-handling-manual-template-msf-rev01a-oct15/161217955
  18. Offshore Vessel Inspection Database (OVID) Programme ... - ocimf, https://www.ocimf.org/document-libary/1008-oviq4-7300-questionnaire/file
  19. INTERIM REPORT SINKING OF THE VESSEL BOURBON RHODE, https://aet.gouvernement.lu/dam-assets/l-administration/transports-maritimes/bourbonrhode/AET-Marine-Safety-investigation-BourbonRhode-interim-final-15042021.pdf
  20. Siem Opal | Aurora Offshore, https://auroraoffshore.com/wp-content/uploads/2025/01/Siem-Opal-vessel-spec-2.pdf
  21. TECHNICAL SPECIFICATION 67M DP-2 ANCHOR HANDLING, https://horizonoffshoreservices.com/wp-content/uploads/2024/05/HOS253-Full-Specification-2.pdf
  22. offshore support vessels 2013 - American Bureau of Shipping (ABS), https://ww2.eagle.org/content/dam/eagle/rules-and-guides/archives/conventional_ocean_service/180_osv_2013/osv_part_5_e-july13.pdf
  23. KFG Pump Assembly Instructions | PDF - Scribd, https://www.scribd.com/document/844227245/SKF-KFG-Auto-Lube-Pump-Stern-Roller-2
  24. Biodegradable Grease | Eco-Friendly Lubricating Greases - OilOnline, https://www.oilonline.store/products/biodegradable-oil/biodegradable-grease
  25. Marine Bearing - INSTALLATION MANUAL, https://thordonbearings.com/docs/default-source/design/marine-bearing-installation-manual.pdf?sfvrsn=daab15ab_24
  26. https://thordonbearings.com/marine/offshore/stern-roller-radial-and-thrust-bearings-and-seals
  27. Stern roller of offshore oil platform anchor boat - Google Patents, https://patents.google.com/patent/CN201472629U/en
  28. Marine Renewable Energy Bearing Applications Product Manual, https://psei.cl/wp-content/uploads/2023/08/Descansos-Autolubricados-para-Generacion-de-Energis-Renovables.pdf
  29. Usability and suitability of high strength mooring chains - Havtil, https://www.havtil.no/contentassets/a55d5b8c269b4d7e9dc164b781ef2022/2022_1060-rapport-usability-and-suitability-of-high-strength-mooring-chains-rev.-1-signed.pdf
  30. AHTS Vessel Specifications and Equipment | PDF | Ships - Scribd, https://www.scribd.com/document/972610279/VOS-Challenge-Specifications-GA
  31. 211' AHTS Built 2004 - Bollard Pull 86 Ton - Mship, https://mship.no/vessels/ahts-vessels/211-ahts-built-2004
  32. BRITOIL DYNAMIC, https://www.britoil.com.sg/hubfs/Vessel%20specs/Britoil%20Dynamic%20Specs.pdf
  33. Featured equipments for sale - Worldoils, https://www.worldoils.com/index.php/equipments?page=5
  34. HF Offshore Fleet, https://www.hf-offshore.com/fleet/
  35. bear-27-03.pdf - Boskalis, https://boskalis.com/media/rathdvla/bear-27-03.pdf
  36. “BB OCTOPUS” - Buksér og Berging, https://www.bube.no/wp-content/uploads/2020/12/Specification_BB-Octopus-1.pdf
  37. Njord Viking, https://www.vikingsupply.com/njord-viking?pid=MySite-Vessel-VesselSpecifications
  38. Anchor Handling Tug Supply Vessels - Pacific Discovery, https://www.tdw.com/wp-content/uploads/2022/06/Pacific-Discovery_v_9.0-TDW.pdf
  39. HTML Maersk Topper, https://www.maersksupplyservice.com/wp-content/uploads/2020/06/HTML-Maersk-Topper-1754.pdf
  40. Aurora Sandefjord, https://auroraoffshore.com/wp-content/uploads/2022/01/sandefjord.pdf
  41. New Regulations for AHT Vessels | PDF | Tugboat | Ships - Scribd, https://www.scribd.com/document/329945244/New-Regulations-for-AHT-vessel
  42. Marine - Hydraulic Seals Australia, https://hsa.com.au/pages/marine
  43. Oil, Gas and Offshore Equipments marketplace, Oil & gas equipments, https://www.worldoils.com/index.php/equipments?page=9
  44. seal.pdf - Stanford Marine, https://stanford-marine.com/wp-content/uploads/2024/03/seal.pdf
  45. 65 tbp FiFi-1 AHTS - VL Maritime Services (Pty) Ltd, https://www.vlmaritime.com/product/b0075-fifi1-ahts/
  46. HOS#483 | 2007 | 46 M | 40 T BP AHTS | For P&C Sale, https://horizonoffshoreservices.com/classifieds/15833/hos483-2007-46-m-40-t-bp-ahts-for-pc-sale/ahts/
  47. 125 Ton AHTS Technical Specification | PDF | Deck (Ship) - Scribd, https://www.scribd.com/document/140142809/125-Ton-AHTSSV-Specification
  48. Yno 249 - Far Santana (Explorer) - Ulstein Group, https://ulstein.com/references/yno-249-far-santana
  49. MV GEMIA | Vantris Energy, https://vantrisenergy.com/wp-content/uploads/2015/10/MV-Gemia.pdf
  50. MOSS 424h AHTS - United Offshore Support GmbH, https://uos.ag/wp-content/uploads/2022/10/MOSS-FINAL-updated-24.10.2022.pdf
  51. Design and Analysis of Stationkeeping Systems for Floating, https://eballotprodstorage.blob.core.windows.net/eballotscontainer/API%20RP%202SK%204th%20Edition%20Ballot%20ID%205772%20Draft%204-27-2022.pdf
  52. VRYHOF MANUAL - Plaisance Pratique, https://www.plaisance-pratique.com/IMG/pdf/Vryhof_Anchor_Manual2015.pdf
  53. AHTS Stern Roller Replaced with Grease-Free Thordon SXL, https://thordonbearings.com/news/2024/10/07/ahts-stern-roller-replaced-with-grease-free-thordon-sxl-bearing-at-sea
  54. Bearings News - MarineLink, https://www.marinelink.com/news/maritime/bearings
  55. Marine Bearings | Ι.& Ε. ΠΑΠΑΔΟΠΟΥΛΟΣ ΑΕΒΕ, https://papadopoulos-sa.com/marine-bearings-orkot/
  56. Orkot Marine Bearings - Ship Technology, https://www.ship-technology.com/contractors/bearings/orkot-marine-bearings/
  57. Marine Composite and Seals - O Rings Limited, UK, https://www.oringslimited.co.uk/products-category/composite/
  58. Zhongyuan Ship Machinery Manufacture (Group) Co. - NauticExpo, https://www.nauticexpo.com/prod/zhongyuan-ship-machinery-manufacture-group-co-200337.html
  59. Page 8 | Buy Grease only the best brands - OlieOnline.co.uk, https://www.olieonline.co.uk/products/grease/page/8
  60. AHTS stern roller bearings replaced with Thordon SXL bearings at sea, https://www.marinelog.com/offshore/ahts-stern-roller-bearings-replaced-with-thordon-sxl-bearings-at-sea/
  61. CIP Composites™ - Zatkoff, https://www.zatkoff.com/catalog/master-catalog/cip-composites/pdf
  62. RepoRt on safety measuRes, http://marinesafetyforum.org/wp-content/uploads/2018/08/NMD-Report_on_Safety_Measures_for_AHV_and_MOU.pdf
  63. OVIQ Sample Master | PDF - Slideshare, https://www.slideshare.net/slideshow/oviq-sample-master/20189200
  64. Stability assessment of anchor handling vessels during operations, https://scispace.com/pdf/stability-assessment-of-anchor-handling-vessels-during-3eu0xj010d.pdf
  65. Fact sheet 2: Anchors and moorings - Offshore Wind Scotland, https://www.offshorewindscotland.org.uk/media/nu4ppiyv/02-anchors-moorings.pdf
  66. Deep Rope Manual | PDF - Scribd, https://www.scribd.com/document/201388613/Deep-Rope-Manual
  67. Abrasion process between a fibre mooring line and a corroded steel, https://www.researchgate.net/publication/284233930_Abrasion_process_between_a_fibre_mooring_line_and_a_corroded_steel_element_during_the_transit_and_commissioning_of_a_marine_renewable_energy_device
  68. T Rex XL | PDF - Scribd, https://www.scribd.com/document/1017709360/t-rex-xl
  69. Ropes for Deep Water Mooring - Offspring International, http://www.offspringinternational.com/wp-content/uploads/2014/05/Deepwater-Morring-Brochure-April-2013.pdf
  70. ADDENDUM - American Petroleum Institute, https://www.api.org/~/media/files/publications/addenda-and-errata/exploration-production/2sm_addendum.pdf?la=en
  71. OTC 20844-PP Fiber Rope Tether Manufacturing, http://www.offspringinternational.com/wp-content/uploads/2014/02/OTC-20844-Fiber-Rope.pdf
  72. Fatigue Assessment of HMPE Mooring Lines on Ships During Side, https://asmedigitalcollection.asme.org/OMAE/proceedings-pdf/OMAE2026/89473/V001T01A037/7643186/v001t01a037-omae2026-180686.pdf
  73. MOORING ROPE MANUAL., https://www.lankhorstropes.com/media/140/temp-downloads/original/11-MEG4-brochure-v1123-72dpi.pdf
  74. US20260217335A1 – A Stern Roller Arrangement | Patsnap Eureka, https://eureka.patsnap.com/patent/US20260217335A1
  75. Maersk Runner - ATSB, https://www.atsb.gov.au/sites/default/files/investigation-reports/mair56_001.pdf
  76. AH Course Manual Version2.8 PDF - Scribd, https://www.scribd.com/document/485447891/AH-Course-Manual-version2-8-pdf
  77. About | Hawse Pro, https://hawsepro.com/pages/about
  78. Tugboat Inspection and Maintenance: Harbor and Ocean Towing, https://marineinspection.app/blog/tugboat-inspection-maintenance-harbor-ocean-towing-compliance-2026