Part 1: System cardDel 1: Systemkort
1. Core Function
Flush-deck hydraulic shark jaws and retractable towing pins form the primary remote line-handling and securing system aboard Anchor Handling Tug Supply (AHTS) vessels1. Remotely actuated from the bridge or cargo-rail panels, towing pins rise above deck forward of the stern roller to laterally contain sweeping towlines, while interlocking jaws clamp high-tension rig chains, wire pennants, and sockets1. When stowed, both assemblies retract flush, leaving the working deck unobstructed2. Remote clamping and stored-energy emergency release minimize manual crew exposure inside hazardous snap-back zones2.
2. Primary Operational Tasks
- Remote Chain and Socket Clamping: Seizing and stoppering 50–166 mm rig anchor chains, wire pennant chain tails, and wire sockets for safe rig anchor connection, disconnection, and chain-to-wire changeovers3.
- Lateral Towline Containment: Raising twin vertical or angular steel guide pins forward of the stern roller to restrict transverse wire or chain sweep within safe stern-centerline sectors2.
- Pitching and Upward-Lead Retention: Deploying hydraulic top-locking flaps, retractable internal arms, or hold-down hooks across the pin gate to prevent towlines from jumping free during vessel pitching in heavy seas or upward line leads1.
- Active Line Centering and Spin Control: Lifting sagging wire sockets with central wire-lifter pins and deploying active pull-down arms or forward centering devices to guide low-tension lines into the jaw throat and restrain torsional spin4.
- Sequenced Emergency Release: Executing rapid, remote load release—retracting wire lifters and towing pins before opening the jaws—under operational line loads (per ISO 24041:2020 load criteria) or dead-ship blackout conditions7.
3. System Interconnections
Inputs: Dedicated high-pressure electro-hydraulic Power Units (HPUs)—typically operating at 18 MPa (180 bar) on standard systems and up to 210–280 bar in vendor heavy-duty catalogs, with 15–37 kW standard motors (and 37–132 kW quoted by a specialist supplier for deepwater packages)—supply pressurized fluid via variable-displacement or dual-pump manifolds backed by main and emergency switchboards8. Stored-energy hydraulic power comes from continuously charged nitrogen accumulator banks paired with a 24 VDC emergency battery supply for dead-ship solenoid actuation16. Operator commands enter from the aft bridge console (or integrated winch workstation), waterproof cargo-rail or deck-mounted local panels, and portable maintenance pendants1. Sensor and switch inputs documented in OEM manuals comprise accumulator charge pressure switches, system line pressure transmitters/gauges, "JAWS POSITION ACCEPT" lock switches, and optional tension monitors10; deck-well proximity sensors are not specified in the reviewed OEM documentation, which relies instead on pressure switches, position-acceptance switches, and physical alignment marks16.
Outputs: Hydraulic cylinders actuate vertical lift and flush-deck retraction of towing pins, wire lifters, and fork or linkage jaws, alongside independent port/starboard jaw clamping and hold-down flap rotation or active pull-down1. Bridge status and control panels output indications for main/emergency power, HPU run state, accumulator charge readiness, hydraulic pressure (bar), and open/closed or locked jaw condition1. Safety outputs drive mandatory working-deck audible alarms during machinery motion, bridge emergency-release buzzers and illuminated push-buttons, critical low-low oil level warnings, and external OK/Failure alarm contacts1.
4. Redundancy and Criticality
Shark jaws and towing pins are safety-critical appliances regulated by Classification Societies (DNV, ABS, LR, BV, CCS, RINA), Flag States including the Norwegian Maritime Directorate/Authority (NMD/NMA), ISO 24041:2020, OCIMF expectations, and mandatory IMO requirements under SOLAS Regulation II-1/3-13 (Resolution MSC.532(107) and MSC.1/Circ.1662, in force since 1 January 2026)4. None of the reviewed Classification Society rule excerpts (including ABS Part 5D11) explicitly mention hydraulic pilot-operated check valves; however, standard hydraulic load-holding practice relies on cylinder-mounted pilot-operated check valves or counterbalance valves to prevent accidental jaw collapse upon upstream hose rupture32, while linkage jaws additionally achieve mechanical over-center locking (>180°) that retains full load without hydraulic pressure21. Vendor compliance guidelines further specify single-failure HPU redundancy via dual pumps or standby accumulators8, while Class and IMO rules mandate protected remote emergency release operable under dead-ship blackouts and all expected combinations of trim and heel7.
Part 2: Technical deep diveDel 2: Teknisk dybdeanalyse
1. Shark Jaw (Karm Fork / Triplex) Mechanical Design
AHTS shark jaws follow two primary mechanical architectures housed inside heavy flush-deck steel support boxes or mounting cassettes1. Across major manufacturers and vessel specifications, Safe Working Loads (SWLs) typically span 100 to 800 metric tonnes (MT) to match high-tensile mooring gear up to 166 mm (and 8 inches in specialized inserts)22.
In vertical-slide fork designs (exemplified by Karmøy Winch's patented Karm Fork™), a single high-tensile steel fork slides vertically inside a fabricated DNV Grade A steel foundation actuated by high-pressure hydraulic cylinders1. A U-shaped or V-shaped jaw throat captures chain links or wire terminations via single-bolt interchangeable U-inserts1. Standard Karm Fork assemblies handle 32–102 mm wire/chain up to 300 MT MBL or 500 MT SWL, while a giant model handles 800 MT SWL, 5.5-inch (approx. 140 mm) chain, and 120 mm wire1.
In interlocking pivoted linkage designs (originated by Triplex in 1983 and supplied by Triplex/MacGregor, Kongsberg Maritime, and Cargotec), independently actuated port and starboard jaws swing upward and inward on toggle linkages5. Triplex jaws automatically rotate misaligned chain links into proper vertical-horizontal seating without winch maneuvering35. Once closed, the Triplex linkage travels past 180° (over-center) into a mechanically locked position that sustains full line tension without manual locking bolts or continuous hydraulic pressure; crew verify lock engagement visually against welded link alignment marks using a supplied calibration ruler16. A central vertically actuated wire lifter pin rises between the open jaws to elevate sagging wire sockets to working height for shackling4. To avoid crushing the wire lifter against closed jaws or chain links, OEM operating manuals enforce strict sequence interlocks: the wire lifter may only extend when both jaws are fully raised, the jaws may only retract when the lifter is fully lowered, and the lifter must never handle chain18. On integrated AHTS decks, twin forward centering devices mounted 1–2 m ahead of the shark jaw swing inward to guide low-tension wires into jaw reach and clamp slackened 76–166 mm chains without inserts to prevent dangerous torsional wire spin during disconnection14.
Equipment Family / Reference Model | Mechanism and Locking Architecture | Rated Capacity (SWL / MBL) | Chain / Wire Sizing and Insert System | Flush-Deck and Handling Features |
|---|---|---|---|---|
Karmøy Winch Karm Fork™ (Type 130976 / Standard / Giant)1 | Vertical-slide high-tensile fork in DNV Grade A steel cassette1 | 300 MT MBL (Type 130976); 300–500 MT SWL standard; 800 MT SWL giant1 | 32–102 mm standard (Insert 130400: 77–102 mm); giant up to 5.5 in (approx. 140 mm) chain and 120 mm wire; single-bolt U-inserts1 | Flush deck retraction; optional tension monitoring and mid-rope stopper1 |
Triplex (MacGregor) Shark Jaw (e.g., H-700)16 | Dual pivoted linkage jaws; >180° over-center mechanical lock21 | 200–700 MT SWL across vessel installations41 | 4 inserts: 2.5–3.5 in, 3.5–5 in, 4.5–7 in, 7–8 in (approx. 64–203 mm); plus fiber-rope inserts35 | Automatic chain link rotation; central wire lifter; ABS Arctic type approval to -40 °C4 |
Kongsberg Maritime (RRM) Shark Jaw10 | Dual jaw with quick-change inserts and bronze retaining bolt10 | Up to 800 MT max working load (large AHTS spec)38 | 4 color-coded chain inserts: C1 50–70, C2 76–95, C3 100–120, C4 125–166 mm; dedicated wire insert10 | Integrated tension reading; single jaw centered by active pull-down pins10 |
Generic Vendor Series (SJ-100 to SJ-700)6 | Fork or Triplex linkage configurations6 | 100–700 MT holding capacity (bollard-pull pairings vary by vendor: 40–200 t vs. 80–560 t)19 | Catalog ranges covering 52–162 mm across model tiers8 | Modular lift-out cassette option; multi-coat offshore preservation44 |
Quick-change inserts are machined from hardened, abrasion-resistant steel (with specialized inserts for fiber ropes) contoured to distribute bearing loads evenly across chain links4. While the reviewed literature confirms compatibility across 76–152 mm chains (within broader 32–203 mm coverage) and wire sockets, the consulted manufacturer manuals and specifications do not differentiate between stud-link and studless rig chains or specify spelter-poured versus resin/mechanical socket constructions1. For wire pennants, Guidelines for Offshore Marine Operations (GOMO) Appendix 11-A prescribes terminating the pennant eye in a heavy-duty socket sized for at least a 76 mm (3-inch) connecting link and recommends fitting a 5-link chain tail (minimum 76 mm, Grade R3) so the shark jaw clamps sacrificial chain rather than crushing wire strands3. GOMO further advises avoiding loads exceeding 30% of line Minimum Breaking Load (MBL) in the jaws, emphasizing that shark jaws serve as static stoppers rather than power-tensioning points3.
Vertical ram guideways elevate the jaws to typical deck working heights around 500 mm (limited by under-deck frame depth, compared with 200 mm on light 30 T harbor units) and retract flush when stowed2. Under ISO 24041:2020 Section 5.5.2, fork-type support boxes must remain watertight during both operation and retraction to prevent water seepage below deck, while triplex-type systems must incorporate sealing or closing devices to seal the housing when inactive6. Detailed mechanical specifications for Triplex flush-deck weather covers were unavailable in the MacGregor brochure reviewed4, though commercial suppliers provide watertight deck covers6, and Kongsberg utilizes gently raised, tapered deck bases on towing pins to shed water and mud10 (alongside mechanically operated parked hatches on its companion ARF 126 Anchor Recovery Frame23).
2. Towing Pins & Hold-Down Locking Flaps
Positioned between the shark jaws and the stern roller, retractable steel towing pins define the horizontal containment corridor for towlines, rig chains, and pennants2. A supplier engineering guide places typical single-set towing pins 3.5–5 m forward of the stern roller centerline at approximately 1.5 m lateral pin spacing5, while twin four-pin deepwater arrays span wider transverse gates (for instance, the official Bourbon Dolphin inquiry recorded a 2.7 m span between the inner starboard and outer port pins45). While utility-tug pins rise roughly 305 mm above deck20, deepwater AHTS pins extend 1,400–1,600 mm above deck level to trap wildly sweeping lines in heavy seas10. When idle, all pins retract flush with the working deck5.
To curb abrasive wear and localized wire bending during transverse sweeping, ISO 24041:2020 Section 5.4 mandates a stiff, flexibly rotating outer sleeve on towing pins17. Manufacturers achieve this using twin identical, symmetrical rotating rollers per pin (Kongsberg TP400 and Triplex divided-roller designs)10, induction-hardened or heat-treated alloy steel sleeves running on grease-lubricated bronze bearings (Smith Berger)12, or external rotating bearings (SHM)46.
Without overhead containment, pitching in heavy seas or steep upward towline leads over the stern roller can lift wires clear over the tops of vertical pins1. Four retention mechanisms address vertical jump-out across commercial AHTS designs. Turntable top-locking flaps (Karmøy Winch and Ulstein) automatically swing high-tensile horizontal plates toward one another as the pins elevate, boxing the line inside a closed square gate1. Internal folding active locking arms (Kongsberg Maritime) retract completely inside slots within the pin body, eliminating open deck recesses and protruding edges that can snag crane pennants during chaser-ring delivery10. Once the slot clears deck level, the arms swing outward at any height, using curved undersides to center lines into a single shark jaw while applying active hydraulic pull-down forces of 50 tonnes total (25 tonnes per side) on standard RRM sets—and up to 60 tonnes on TP480X1600 pins—to seat and rotate heavy chains without deck crew intervention10. Alternatively, angular close-top pins (Triplex, Ulstein, and Deyuan) incline inward to meet overhead in an A-frame trap4, while independent hold-down hooks (Smith Berger and KMT) employ separately actuated heat-treated cast steel hooks beside vertical pins12.
Lateral load ratings for AHTS towing pins typically range from 160 to 300 MT SWL36, extending to 400–500 MT SWL in heavy vendor catalogs22. Smith Berger dimensions its pin and hook assemblies to withstand the rated wire rope's breaking strength under a 45° horizontal wrap on the pin and a 35° upward lead from the hold-down hook (e.g., Model 12T414-2HD rated for the 494,000 lb breaking strength of 2-1/4-inch wire)13, whereas Data Hidrolik publishes lateral SWLs as a function of 30°, 60°, and 120° bollard sweep angles24. Under ISO 24041:2020 Section 5.2.1.1, component stresses at SWL cannot exceed 0.67 times material yield strength (0.67 Y)17. For integrated sizing, DNV Type Approval TAS000023X requires the paired shark jaw SWL to exceed maximum winch hoisting capacity by 20%29, while vendor summaries of OCIMF guidance cite minimum holding capacities of 1.1–1.25× vessel bollard pull8.
3. Hydraulic Control Circuits & Blackout Emergency Release
Dedicated electro-hydraulic HPUs—sited close to the stern cassette, typically inside the steering gear room—run on ISO VG 68 hydraulic oil (minimum viscosity index 90) at 18–28 MPa (180–280 bar)5. Standard 100–700 MT catalog packages use 15–37 kW motors (e.g., 34 kW on Karmøy combined units), while vendor heavy-duty specifications range up to 37–132 kW with variable-displacement pumps or dual-pump manifolds, IP56 cabinets, and swaged hoses or SAE-flanged rigid piping free of threaded high-pressure fittings1.
Although AHTS low-pressure anchor-handling winches routinely employ proportional pressure-compensated directional control valves (such as Kongsberg's E26 valve) for stepless speed modulation55, the reviewed OEM shark-jaw and towing-pin manuals instead document discrete solenoid-operated directional valves commanded by continuous-hold push buttons or selector switches1. On the cylinder load-holding side, neither the reviewed ABS Part 5D excerpts11 nor the available OEM shark-jaw manuals specify internal valve schematics by name. In standard marine hydraulic engineering, cylinder protection separates into two distinct valve types32. Pilot-operated (PO) check valves admit free flow to extend or clamp actuators and provide zero-leakage poppet seating against upstream hose rupture, unlocking only when pilot pressure reaches roughly 1/3 to 1/10 of trapped cylinder pressure32. However, because PO check valves are strictly non-modulating on/off devices, opening them against an overrunning load induces uncontrolled descent and severe hydraulic shock32. Counterbalance valves—often paired with cross-over relief valves on deck winches and lifting circuits57—likewise provide zero-leakage static holding but continuously modulate return-line backpressure to stabilize lowering under overrunning loads32. In Triplex jaws, mechanical >180° over-center linkage locking provides an independent, purely mechanical safeguard against hydraulic pressure loss21.
To ensure positive release during a total "Dead Ship" blackout (loss of both main and emergency generators), the hydraulic circuit integrates a dedicated nitrogen-loaded accumulator bank (housed in the steering gear room) and a 24 VDC emergency battery bus16. The HPU keeps the accumulators continuously charged; once a pressure switch senses full charge, a damping valve isolates surge and illuminates the bridge "Accumulator Charged" indicator18. Vendor engineering specifications cite a minimum 50 L pre-charged accumulator volume sized to sustain full jaw clamping for 30 seconds without HPU power plus execute release8.
Per IMO MSC.1/Circ.1662 Section 3.1.8.1 and NMD regulations, emergency release must automatically retract any pins or fittings that could foul the escaping line7. Depressing two protected emergency-release push buttons simultaneously (guarded against accidental actuation) overrides the "JAWS POSITION ACCEPT" operational lockout, sounds bridge buzzers and deck alarms, and vents accumulator pilot pressure through emergency solenoids in a fixed sequence: first retracting the wire lifter pin and all guide/towing pins flush, then immediately opening and retracting the jaws7. Triplex H700/S200 manuals document full opening to deck level within 4–7 seconds on accumulator power16 (with vendor literature citing under 2 seconds for powered quick release35, well within NMD's 10-second line-tension release rule27). Under ISO 24041:2020 Section 5.2.3, emergency release mechanisms must remain capable of disengaging under high live-line friction loads17:
Shark Jaw Rated SWL Tier | ISO 24041:2020 Emergency Release Formula | Illustrative Rated SWL | Required Emergency Release Load |
|---|---|---|---|
Below 1,200 kN (~122 t) | 100% of SWL | 1,000 kN (~102 t) | 1,000 kN (100% SWL) |
1,200 to 5,000 kN (~122–510 t) | 0.20 × SWL + 1,000 kN | 3,000 kN (~306 t) | 1,600 kN (~163 t / 53.3% SWL) |
Above 5,000 kN (~510 t) | 0.40 × SWL | 7,000 kN (~714 t) | 2,800 kN (~286 t / 40.0% SWL) |
Under IMO Resolution MSC.532(107) and MSC.1/Circ.1662 (mandatory via SOLAS Regulation II-1/3-13 since 1 January 2026), any emergency release must be followed by a thorough inspection of the entire stopper system before returning the equipment to service7.
4. Hull Structural Integration & Load Paths
AHTS aft-deck cassettes resist static holding loads of 500–800+ MT36 alongside severe transient shock loads—estimated in vendor documentation at 2–3× static chain tension when breaking anchors free of the seabed8 (for comparison, DNV Lifting Standard No. 2.22 specifies a 1.5 dynamic factor on adjacent Kongsberg Anchor Recovery Frames23). Three orthogonal load vectors act simultaneously on the cassette: longitudinal aft pull toward the stern roller9, transverse lateral pin bearing across sweeping angles up to ±90°11, and vertical uplift against hold-down flaps (rated up to 35° upward leads13) alternating with downward compression during steep stern catenaries or 50–60 tonne active pin pull-down10.
Manufacturers pre-assemble jaws and pins inside heavy rolled-steel support boxes (e.g., DNV Grade A or ABS Part 2 steel)1. While ISO 24041:2020 Section 5.5.1 requires the support box itself to sustain full SWL at working elevation (≤ 0.67 Y)17, DNV Type Approval TAS000023X Section 9 explicitly excludes the support and welding of the complete housing into the deck structure from equipment Type Approval29. Shipyards must therefore design and class-approve the under-deck foundation separately using certified welders29.
Rather than sitting atop main deck plating via doubler plates, the cassette penetrates a thickened flush deck insert plate tied into surrounding aft cargo-deck plating (typically ≥ 12 mm thick and rated for 7.5–15 t/m² distributed deck loads)11. Below deck, the cassette side plates extend downward and weld directly into heavy longitudinal box girders (trusses), transverse web frames, and watertight transverse bulkheads, frequently fitting between two primary longitudinal frames—whose depth constrains maximum vertical cylinder travel5. For supporting structures under towing hooks, winches, bollards, and bitts (a structural design framework referenced alongside aft towing foundations), ABS Marine Vessel Rules Part 5D strictly prohibits doubler plates between foundations and deck plating, requiring a thicker insert plate instead11. ABS Part 5D sizes those towing-gear foundations for 2× static bollard pull (or 2× estimated escort braking/steering force, whichever is greater) applied horizontally across ±90° from centerline, limiting normal stress to 0.75 Y and shear stress to 0.45 Y, verified against plate buckling and direct Finite Element Analysis (FEA)11. Vendor AHTS design specs also note primary structural fatigue verification to 10⁶ load cycles8.
5. Tripping/Girding Hazards & Maintenance
Tripping, Girding, and Capsizing Mechanics: If a loaded towline or rig chain passes outside or over the towing pins and sweeps abeam (large horizontal angle α off centerline), it creates a long transverse heeling arm high above the hull's center of lateral resistance45. When opposed by maximum lateral thruster/rudder output (self-tripping) or hull hydrodynamic drag during sideways drift (tow-tripping), the resulting heeling moment combines with vertical downward tension at the stern roller that trims the vessel by the stern and reduces aft freeboard63. Once heel immerses the open working-deck edge, green water floods across the stern, sharply eroding the righting lever (GZ) curve and causing rapid capsize63.
The capsize of the Norwegian AHTS Bourbon Dolphin on 12 April 2007 while deploying 18-tonne anchor #2 (~2 km / 300-tonne chain) for the semi-submersible Transocean Rather west of Shetland illustrates how swiftly pin-bypass girding escalates45. Operating in 32-knot winds, 2–3 m significant waves, and 1–2 knot currents with a spare anchor lashed on the port cargo rail and its roll-reduction tank likely active, the drifting vessel agreed to lower its inner starboard towing pin45. Chain pressure initially jammed the pin until the Master altered heading slightly to starboard to ease tension70. Once the inner starboard pin retracted, the loaded chain whipped 2.7 m across the stern to slam against the outer port towing pin (as established by eyewitness testimony in the official Norwegian inquiry NOU 2008:8; secondary press commentary occasionally misidentifies the outer pin side as starboard)45. Bourbon Dolphin heeled roughly 30° to port for ~15 seconds, briefly recovered after its starboard main engine stopped amid a momentary blackout, then rolled over to port and capsized at 17:08, killing 8 of the 15 people aboard45.
Prompted by post-Bourbon Dolphin NMD corrective directives, IMO Resolution MSC.415(97) (amending Part B of the 2008 Intact Stability Code, §§2.7–2.8) requires anchor-handling stability assessments across horizontal sweep sectors (α in ≤ 5° increments, generally ≥ 5°) using longitudinal (x) and transverse (y) pin coordinates and vertical downward vector angle (β) at maximum heeling moment64:

where h is the vertical distance from the propulsion force center to the pin/line restriction, BP is bollard pull, and Fp is permissible wire tension65. Permissible line tension must keep the static equilibrium heel angle (φe, first intersection of heeling and righting levers) below the least of (1) the angle where GZ equals 50% of maximum GZ, (2) the working deck-edge immersion angle, or (3) 15°65. Stop pins must physically block outboard wire travel, and bridge conning positions must display sector tension tables, emergency release delays, and available continuous bollard-pull curves accounting for thruster and winch electrical loads64.
Jaw Insert Cracking and Linkage Yielding: Repeated 2–3× seabed breakout shock loads8 and lateral blows from tilting anchors21 subject hardened jaw inserts and toggle linkages to severe localized stress. Explicit OEM non-destructive testing (NDT) schedules and field crack-rate statistics for shark jaw inserts were absent from the reviewed sources; operational standards rely on immediate visual inspection after impact loads or emergency release7, checking welded Triplex linkage alignment marks with a calibration ruler to confirm >180° lock geometry16, and periodic calibrated load-cell pull testing per ISO 24041 and IMO MSC.532(107)30. General academic corrosion-fatigue investigations confirm that chloride and sulfate pitting acts as a sharp geometric stress raiser that accelerates fatigue crack initiation75, though those studies analyzed submarine cable armour, 410 stainless turbine blades, and aluminum structural alloys rather than shark jaw steels directly.
Subsea Seawater Seal Corrosion: Aft working decks experience continuous green-water immersion, brine, and mud washdown8. Saltwater pitting on exposed actuator rods and pivot pins degrades sealing surfaces and cylinder life, though specific elastomer seal-failure rates were not documented in the reviewed manuals. Marine specifications mitigate seawater corrosion through stainless steel cylinder rods, high-grade duplex interfaces, synthetic bushings, grease-lubricated bronze bearings, three-coat marine paint systems, and continuous HPU motor space heating8.
Mud and Debris Fouling Inside Flush-Deck Wells: Because AHTS vessels routinely transfer oil-based mud (OBM), water-based mud (WBM), and brine across the aft deck42, drilling mud, sand, and debris wash into open deck pockets around jaws and pin housings—obstructing full flush retraction or full over-center jaw locking10. Design countermeasures include Kongsberg's internal-slot locking arms and gently raised, tapered deck bases that eliminate debris-trapping deck recesses10, as well as modular lift-out shark jaw cassettes for shoreside overhaul44. Consistent with Marine Safety Forum Safety Alert 21.0480, anchor-handling maintenance procedures strictly require venting and emptying all nitrogen hydraulic accumulators (and isolating HPU power) before clearing debris or servicing components inside a shark jaw or towing pin well18.
References
- User Manual | PDF | Valve | Pump - Scribd, https://www.scribd.com/document/853371783/User-manual
- Shark jaws for anchor handling vessel - Kongsberg Maritime, https://www.kongsbergmaritime.com/products/deck-machinery-and-handling/Deck-safety-and-load-control/shark-jaws-ahts/
- Appendix 11-A, https://cdn.prod.website-files.com/64952ab0909f7042f518690c/664f0d79d47c54a8c9cf6445_Appendix%2011-A-rev-2.pdf
- Anchor Handling and Towing Vessels - MacGregor, https://www.macgregor.com/globalassets/picturepark/imported-assets/83837.pdf
- Shark Jaw & Towing Pin: Complete Buyer's FAQ Guide, https://hiqool.com/shark-jaw-and-towing-pin-the-ultimate-faq-guide/
- Hydraulic Triplex Shark Jaw - weitong marine, https://www.weitongmarine.com/products/hydraulic-triplex-shark-jaw-434
- MSC.1/Circ.1662 - Guidelines for Anchor Handling Winches, https://www.iomshipregistry.com/media/saknhaa1/msc1-circ1662-guidelines-for-anchor-handling-winches.pdf
- Shark Jaw & Towing Pin Systems for AHTS Vessels | SharkJaw, https://sharkjaw.net/applications/ahts-vessel/
- Anchor Handling Operations Manual | PDF - Scribd, https://www.scribd.com/presentation/273155059/Anchor-Handling-Equipment
- NEW CONCEPT FOR TOW PINS AND SHARK JAW, 100 - Kongsberg, https://www.kongsberg.com/contentassets/e667d80fc4904e9f96ac905cb141d342/28.dm_2p_10.10.11.pdf
- https://ww2.eagle.org/content/dam/eagle/rules-and-guides/archives/other/1_marinevesselrules_20211/mvr-part-5d-july21.pdf
- Towing Pin / Stern Roller Assemblies - JH Menge, https://jhmenge.com/wp-content/uploads/tow_pin_stern_roller_assemblies.pdf
- Tow Pin / Stern Roller / Two Pin, One Hook - Smith Berger Marine, Inc., https://www.smithberger.com/tow_pin_2_pin_1_hook.html
- Centering device for anchor handling vessel - Kongsberg Maritime, https://www.kongsbergmaritime.com/products/deck-machinery-and-cranes/anchor-handling-vessels/centering-device-ahts/
- Stop pins for anchor handling vessel - Kongsberg Maritime, https://www.kongsbergmaritime.com/products/deck-machinery-and-handling/Deck-safety-and-load-control/stop-pins-ahts/
- Triplex Shark Jaw APM H-700 Manual | PDF | Pump | Valve - Scribd, https://www.scribd.com/document/977899005/1-Manual-h700-s200-Apm
- INTERNATIONAL STANDARD ISO 24041, https://cdn.standards.iteh.ai/samples/77625/0204aeb6186a4fafb30386db09b651df/ISO-24041-2020.pdf
- Shark Jaw and Towing Pin Manual | PDF | Valve | Pump - Scribd, https://www.scribd.com/document/201900735/Cm-p4766-69-Sjtp-Issue-A
- Hydraulic Towing Pin with Shark Jaw - Hi-Sea Marine, http://www.hiseamarine.com/hydraulic-towing-pin-with-shark-jaw-5467.html
- Advanced Marine Shark Jaws Set New Standard for Anchor, https://www.deyuanmarine.com/Advanced-Marine-Shark-Jaws-Set-New-Standard-for-Anchor-Handling-Safety-id44107855.html
- TRIPLEX - SHARK JAW SYSTEM., https://studfile.net/preview/5155240/page:10/
- SharkJaw — Shark Jaw & Towing Pin Systems, https://sharkjaw.net/
- ARF 126 ANCHOR RECOVERY FRAME - Kongsberg, https://www.kongsberg.com/contentassets/e667d80fc4904e9f96ac905cb141d342/41.dm_1p-12.05.15.pdf
- Towing Pins - Data Hidrolik, https://www.datahidrolik.com/en/products/towing-pins/
- Karm Fork - Karmøy Winch AS, https://www.karmoy-winch.no/karm-fork/
- Shark Jaws - Damen Marine Components, https://www.damenmc.com/products/deck-equipment/shark-jaws
- Regulations of 19 December 2014 No. 1853 on the construction and, https://www.sdir.no/siteassets/engelske-forskrifter-pdf/repealed_19-december-2014-no.-1853-construction-and-supervision-of-small-cargo-ships.pdf
- DYNAMIC POSITIONING | DECK EQUIPMENT | STEERING GEARS, https://pmh.no/wp-content/uploads/2017/08/pmh_brochure_eng_web_.pdf
- TYPE APPROVAL CERTIFICATE - DNV, https://approvalfinder.dnv.com/api/approval/document?id=TAS000023X
- Anchor Handling Winches – Incoming New Requirements, https://north-standard.com/insights-and-resources/resources/news/anchor-handling-winches-incoming-new-requirements
- 01/2026: New SOLAS requirements for anchor handling winches | LR, https://www.lr.org/en/knowledge/class-news/01-26/
- Pilot Check vs Counterbalance Valve: Load Control and Selection, https://adifferhydraulics.com/pilot-operated-check-valve-vs-counterbalance-valve/
- Hydraulic Load Holding: P.O Checks vs. Counterbalance Valves, https://qualityhydraulics.com/blog/valves/load-holding-po-checks-or-counterbalance-valves
- PILOT OPERATED CHECK VALVES - Bosch Rexroth, https://apps.boschrexroth.com/products/compact-hydraulics/ch-catalog/pdf/Pilot_Operated_Check.pdf
- TRIPLEX SHARK JAW - Sanger Met, https://sangermet.com/dane/pliki/e7/54/e754cac5022b490/Triplex_Shark_Jaw_and_Guiding_Pins.pdf
- IMR/ ROV with 150 MT SWL Knuckle Boom Jib Crane Capabilities, https://horizonoffshoreservices.com/wp-content/uploads/2024/10/1999-85M-DP2-MPSV-AHTS-Oct-2024.pdf
- EQUIPMENT LAYOUT AND FUNCTION (cont'd) - BigCommerce, https://cdn11.bigcommerce.com/s-ya3gab2q5e/content/pdf/BP102240.pdf
- Aurora Sandefjord, https://auroraoffshore.com/wp-content/uploads/2022/01/sandefjord.pdf
- Triplex Type Shark Jaw, http://www.cqhisea.com/Triplex-Type-Shark-Jaw-119-990-1.html
- First of Robert Allan Ltd.'s RAstar 4000-DF Class Dual Fuel Extreme, https://ral.ca/2017/05/26/rastar-4000-df-delivered-ostensjo/
- Oil, Gas and Offshore Equipments marketplace, Oil & gas equipments, https://www.worldoils.com/index.php/equipments?page=7
- Multipurpose AHTS 'Boulder' - JD-Contractor A/S, https://www.jdcon.dk/sw/frontend/downloadfile.asp?id=604681
- 100~700T Triplex type Hydraulic Shark Jaw and Towing Pins, https://www.deyuanmarine.com/100-700T-Triplex-type-Hydraulic-Shark-Jaw-and-Towing-Pins-pd417354.html
- Triplex Shark Jaws Operations and Emergency Release ... - YouTube, https://www.youtube.com/watch?v=sgMxlliW_6A
- 9 Forliset - NOU 2008: 8 - regjeringen.no, https://www.regjeringen.no/no/dokumenter/nou-2008-8/id504445/?ch=11
- Towing Pins - SHM Solutions, https://www.shmsolutions.no/en/deck-equipment/towing-pins
- Featured equipments for sale - Worldoils, https://www.worldoils.com/equipments?page=27
- Towingpins – Karmøy Winch AS, https://www.karmoy-winch.no/towingpins/
- SPECIFICATION FOR 75 METRE ANCHOR HANDLING SUPPLY, https://maritimeexpert.wordpress.com/wp-content/uploads/2016/12/75m_supply-vessel-full-specification_ahsv.pdf
- Towing Roller & Norman Pin - KMT SUBMARINE, http://www.kmtsubmarine.com/us/products/TRNP.asp
- 78m AHTS Outline Spec 20150331 - MK Marine, http://mkmarine.com.sg/specifications.html?4
- MP VELOCE - Marco Polo Marine, https://marcopolomarine.com.sg/upload/VELOCESPEC.pdf
- TECHNICAL SPECIFICATION 67M DP-2 ANCHOR HANDLING, https://horizonoffshoreservices.com/wp-content/uploads/2024/05/HOS253-Full-Specification-2.pdf
- TOW PIN/STERN ROLLER - ShipServ, https://www.shipserv.com/ShipServ/pages/profiles/53736/specsheets/0102SS0619w.pdf
- Towing Winches for anchor handling vessels - Kongsberg Maritime, https://www.kongsbergmaritime.com/products/deck-machinery-and-cranes/anchor-handling-vessels/anchor-handling-and-towing-winches-ahts/
- The pilot operated checkvalve, https://www.hydraulicweb.nl/hydraulics/gsttslk_e.htm
- Hydraulic Towing Winch Operation Guide | PDF | Clutch - Scribd, https://www.scribd.com/document/329660827/600-KN-Towing-Winch-Manual
- 5229-30 Operation Maintenance Manual - Scribd, https://www.scribd.com/document/1031350033/5229-30-Operation-Maintenance-Manual
- Anchor handling operations Rules & Standards – ongoing initiatives, https://riggflytt.com/wp-content/uploads/2025/05/07-DNV.pdf
- rules for building and classing - offshore support vessels 2019, https://ww2.eagle.org/content/dam/eagle/rules-and-guides/archives/conventional_ocean_service/180-offshoresupportvessels/osv-part-5-jan-19.pdf
- 125 Ton AHTS Technical Specification | PDF | Deck (Ship) - Scribd, https://www.scribd.com/document/140142809/125-Ton-AHTSSV-Specification
- Palfinger Marine Crane Product Catalogue | PDF - Scribd, https://www.scribd.com/document/445350484/Pf-Product-Brochure-2016
- Guidelines for Offshore Marine Operations, https://cabmakassar.org/wp-content/uploads/2018/07/GUideline-of-Marine-Operation-GOMOfinal.pdf
- RESOLUTION MSC.415(97) (adopted on 25 November 2016, https://wwwcdn.imo.org/localresources/en/KnowledgeCentre/IndexofIMOResolutions/MSCResolutions/MSC.415(97).pdf
- MSC.415(97) Amendments to Part B of the International Code on, https://rise.odessa.ua/texts/MSC415_97e.php3
- 200813 Anchor handling tug capsize - Nautical Institute, https://www.nautinst.org/resources-page/200813-anchor-handling-tug-capsize.html
- Stability assessment of anchor handling vessels during operations, https://scispace.com/pdf/stability-assessment-of-anchor-handling-vessels-during-3eu0xj010d.pdf
- Bourbon Dolphin Case History | Steamship Mutual, https://www.steamshipmutual.com/bourbon-dolphin-case-history
- Bourbon Dolphin-ulykken - Store norske leksikon, https://snl.no/Bourbon_Dolphin-ulykken
- Inquiry evidence provides insight into tragedy - Riviera Maritime Media, https://www.rivieramm.com/news-content-hub/news-content-hub/inquiry-evidence-provides-insight-into-tragedy-51623
- Bourbon Dolphin Report - gCaptain, https://gcaptain.com/bourbon-dolphin-report/
- AHTS Bourbon Dolphin - Wikipedia, https://en.wikipedia.org/wiki/AHTS_Bourbon_Dolphin
- Maersk Training Anchor Handling Simulator Course - pdfcoffee.com, https://pdfcoffee.com/maersk-training-anchor-handling-simulator-course-pdf-free.html
- Towing Pin and Shark Jaw Pull Test - Louis Safety, https://louissafety.com/towing-pin-and-shark-jaw-pull-test/
- Corrosion Fatigue Modelling of Dynamic Submarine Cable Armour, https://www.diva-portal.org/smash/get/diva2:1989670/FULLTEXT01.pdf
- (PDF) Pitting Corrosion Damage for Prediction Useful Life of, https://www.researchgate.net/publication/272088235_Pitting_Corrosion_Damage_for_Prediction_Useful_Life_of_Geothermal_Turbine_Blade
- The Effect of Corrosion Damage Morphology on Fatigue Crack, https://libraetd.lib.virginia.edu/public_view/vt150j72v
- Anchor Handling Mearsk | PDF | Transmission (Mechanics) - Scribd, https://www.scribd.com/doc/308824986/Anchor-Handling-Mearsk
- Revised Marine Operations Manual 2023 | PDF - Scribd, https://www.scribd.com/document/962925586/Marine-Op-Manual
- Safety Alert, https://www.marinesafetyforum.org/wp-content/uploads/2021/02/msf-safety-alert-21.04.pdf
- AH Course Manual Version2.8 PDF - Scribd, https://www.scribd.com/document/485447891/AH-Course-Manual-version2-8-pdf